I am thinking about getting into reloading 7.62x39 and want to shoot a cheap cast bullet i am wondering if i can take a 158gr cast 38 special bullet and size it down thru a lee sizer to .311 so i can load it in the 7.62
Printable View
I am thinking about getting into reloading 7.62x39 and want to shoot a cheap cast bullet i am wondering if i can take a 158gr cast 38 special bullet and size it down thru a lee sizer to .311 so i can load it in the 7.62
sorry, you'll either break whatever press you have or the sizing die itself trying to squeeze the .358 bullet through a .311 sizing die.
Spend the $20-25 dollars and buy a LEE 155gr .311 bullet that was designed for the 7.62x39 cartridge and that works great in SKSs, AKs, and other rifles (I use it in my 7.62x39 chambered Turk small-ring Mauser).
Bruce
thanks that's kinda what i fiqured i was just trying to keep it simple and not have to spend the time casting more calibers
Lee's 311x155 was made for the 7.62x39.
I shoot the Lee gas checked .312 160 gr. tumble lube version of the X39 mold in a couple of my SKS rifles with excellent results. Bullet drops close to .314 using WW alloy,gas checks are applied with the Lee .314 push through sizer.
I've pushed it up over 1900 fps. gas checked using two coats of Alox/JPW lube and 2400 powder. I also shoot the same bullet in my Mosin M44 with equal results. Shoots pretty decent in my Sav. 99 in 300 Sav. as well.
where are u guys getting your brass from, the 7.62x39 i keep finding is really expensive and how many times are u reloading the brass
I'm up to 10x on some of mine. Swaping & selling and through several learning curves it can be formed from other things I've found laying around like (after I swapped it for 357) 6.8 Rem run it through the sizer cut the neck . If your a little bit skilled and really want to work for the free brass you can turn the rim off 30-30/32 Win spcl and cut a new groove run it through your sizer and cut off the neck. The 3030/32 Win trick works for 25/30/32 and 6.8 Remingtons too.
My best successes w/an sks are here leading was a bugger past the gas port.
http://castboolits.gunloads.com/showthread.php?t=122932
Good luck
I bought mine local or online either from Graf & Son or people that had it for sale on several different forums in the components trading or selling sections. I currently have six reloads on some of my brass and my SKS rifles don't beat the brass up.
The cast bullet loads especially the 12.5 gr. loads of 2400 that cycle my Chinese SKS ( your results may vary ) don't put much wear and tare on the brass and drop it right at my feet. I use mainly Win. and Prvi Partizan brass which uses LR primers and I have about 100 Rem. cases that use SR primers.
I bought an initial box or two of Remington 125gr SP to start but the other several hundred cases I have in 7.62x39 have come about through trades or range pickups.
There are a lot of non-reloaders out there who will buy the good boxer brass cartridges but leave them on the range thinking they are cheap mil-surp berdan brass. Its an easy trick to lean over and see if its reloadable. If its good, it goes in the range bag for cleaning and processing later at home. If its berdan or steel/polymer coated than it still gets picked up and thrown in the range trash bin.
Bruce
I use the Lee .312 155 gn. for my AK-47. You can find range brass or you can purchase un-primed 7.62x39 brass from Midway or other brass specialty sites. Just search on google for 7.62x39 brass for reloading. And you can buy by the 50 count for about $20-$25. Top Brass and Affordable Brass & Bullets come to mind. Winchester, Privi Partisan and Sellor & Belot are cartridges that are boxer primed. Hope this helps. BC
I've got over 21 reloads on IMI and winchester brass, but I anneal every 5th reload or so, and don't shoot max loads.
After slugging my barrel I use a .314 diameter boolit.
Is there a way to make these higher powered cast loads not cycle the bolt. In other words, make an SKS into a single shot, bolt action?
Pretty easy for me , mine has a gas cut-off for the grenade launcher kit. Some guys have reported removing the gas piston from the tube.
Take the gas piston out?Quote:
Originally Posted by Westwindmike
Larry Gibson
That's what I was thinking. Just wanting to make sure it was safe to do.
I have a Ruger Mini-30, and it came with 470 chinese steel cased, berdan primed cartridges. I've pulled the boolits from them, and reloaded them with lead boolits, as this rifle looks to be either unfired, or shot very little, and so I'm planning on only feeding this rifle a diet of lead cast boolits. Once these cases are fired, I'm planning on reloading them. I already have the proper berdan primers, an RCBS berdan decapper, and reloading dies as well, so I'm going to reload them at least once, maybe more, depending on how the cases hold up. I also have 200 brass cases I traded for, in case my plans for reloading the steel cases doesn't work. The chicom ammo I have has 2 different style casings, one has a brown color, and are polymer coated, the others have a copper wash on them (both inside the case, and out) that might also have a polymer or possibly laquer coating on them, but if so, it's a very think coating, as it feels like a metallic finish, not a plastic one (such as coated ammo has).