Anyone know what I have here?

Printable View

06-22-2018, 07:52 AM
cwlongshot

Anyone know what I have here?

Hello guys!

I borrowed this mold form a good friend.

I thought it was a RANCH DOG bullet. (I see it has grease groves and the RD has tumble grooves) I had been wanting for some time. I thought it was a .358 (ish) 180G GC bullet.

It is a alum mold I assumed was a LEE, but maybe not... It is a six holler. I cast up 20# of them that tested to about 12bhn hour after casting.
Couple days back I powder coated about 50 and sized them to .360. (Looking to use in a 357Mag revolver, Marlin lever and two 357 MAX carbines.) Well, my case gauge tells me that these are too long. They protrude out the front by a good 3/32" SO, now I am wondering what bullet I actually have as this shouldn't bee the case if this is what I thought it was...

http://img.photobucket.com/albums/v4...pstiwlef4i.jpg
http://img.photobucket.com/albums/v4...psqleaf2ed.jpg

http://img.photobucket.com/albums/v4...pslnhq3di3.jpg
http://img.photobucket.com/albums/v4...psfxt4tik6.jpg

http://img.photobucket.com/albums/v4...pseaok7i6v.jpg

http://img.photobucket.com/albums/v4...psys1vdrs4.jpg
http://img.photobucket.com/albums/v4...psk3jkiwcx.jpg

I'm not much worried about use in the maximums as I know they have long throats and being single shots length isn't a function problem. But in the revolvers and Marlin, they aint gonna work without trimming cases. Or loading in 38 spl cases...

Any & all comments and suggestions welcome!

CW
06-22-2018, 09:28 AM
Nueces

A few of your excellent photos of the mould and any markings would help a lot.
06-22-2018, 11:10 AM
Dusty Bannister

The archives are a wonderful source if anyone cares to take a look. Maybe this is the mold you are looking for?

http://castboolits.gunloads.com/show...our-order-here
06-22-2018, 11:19 AM
EMC45

I have the RD mold and that is not the bullet from that mold.
06-22-2018, 12:01 PM
mdi

Are they too long for your cylinder or your gauge? Do the bullets stick out the front of the cylinder? (I quit using case/cartridge gauges when I had an epiphany; Ill be shooting the cartridge out on my barrels, not out of a gauge...).
06-22-2018, 12:05 PM
dondiego

Looks like they would work pretty well in a .35 REM.
06-22-2018, 01:11 PM
Grmps

What are the measurements of the boolit
06-22-2018, 01:26 PM
Dusty Bannister

Quote:

Originally Posted by Grmps

What are the measurements of the boolit

You could make it work for your 357, warm some gas checks on a hot plate, put them in the bottom lube groove in your mold before you cast the boolit (tweezer work) -- presto shorter boolits.

Don't think that is going to work with a base pour mold.
06-22-2018, 07:02 PM
Kraschenbirn

Have you actually tried these in your revolvers and levergun? Revolver cylinders aren't all the same length. Heavy boolit rounds that I shot through an original (Monson) Dan Wesson for IHMSA were too long for my Ruger BH and my Marlin is much more picky about loaded rounds that are shorter than factory than those that are slightly longer. If nothing else, you can seat those to fit your cylinder(s) and apply a taper crimp instead of using the crimp groove...which is what I do with PC'd Arsenal 360-162s for my GP100 MC.

Bill
06-22-2018, 09:04 PM
Grmps

Quote:

Originally Posted by Dusty Bannister

Don't think that is going to work with a base pour mold.

OOPs, you're right. Brian was on vacation :killingpc
06-22-2018, 11:19 PM
Kraschenbirn

Quote:

Originally Posted by Grmps

OOPs, you're right. You could machine 1/4 " (+/-) off the mold to make it shorter.

Uh-Uh...that won't work either. Shortening the base would have no effect on loaded OAL if he continues to roll crimp into the crimp groove.

Bill
06-23-2018, 08:00 AM
John J

Greetings
maybe this is it....http://www.accuratemolds.com/bullet_...=36-185M-D.png

John J
06-23-2018, 08:32 AM
jules

2 Attachment(s)

Attachment 222567
Attachment 222569
06-23-2018, 10:34 AM
Dusty Bannister

I posted a link to a group buy mold in post #3. If you looked at that link, particularly post #47 you will see the bullet I think you have been casting. That bullet drawing was done in 2004? If you still have samples or want to copy the drawing, any of the current mold makers can replicate it for you, but it will be in a 5 cav or less configuration. I think that only Lee produces a 6 cav mold configuration.

Based upon the age of the drawing and probable production, you will have to look closer at the mold blocks for the 5 digit mold number. That will tell Lee what they made, but the numbers may be meaningless to anyone else. When the blocks are installed on the mold, the marks are on the end of one block closest to the handle hinge. On the bottom of the handles so you will have to turn the mold over to even find the numbers. If you are really lucky, it will give the information in the newer terminology as C358-180-RF.
Dusty
06-24-2018, 10:35 AM
10x

Quote:

Originally Posted by cwlongshot

Hello guys!

I borrowed this mold form a good friend.

I thought it was a RANCH DOG bullet. (I see it has grease groves and the RD has tumble grooves) I had been wanting for some time. I thought it was a .358 (ish) 180G GC bullet.

It is a alum mold I assumed was a LEE, but maybe not... It is a six holler

http://img.photobucket.com/albums/v4...pslnhq3di3.jpg

I am curious as to the marks on the bullet on the right????
06-24-2018, 11:09 AM
sigep1764

Looks like it fell on the floor and whatever was stuck to it scratched it as it went through the sizer.
06-25-2018, 09:15 AM
cwlongshot

Probably or it fell over when PC in oven.

Jules,
That NOE 358-180 (185) looks real close and NOE does alum molds. (I have a few)

Thanks guys!

CW
06-26-2018, 12:23 PM
jules

I shoot them in a GP100 and a S&W 686.