Printable View
I picked up a decent condition single cavity Lyman 311467 mold with
handles today for $35.
Anyone have experience with this design? I have read that the Loverin designs
are good, but I have not tried one yet. Is it normal to fill all the grooves with
lube or just the ones inside the case neck?
Bill
A Lot of old timers swear by this in the 30-06. It was very well thought of back in the 60's when I was a whippersnapper.
I bought a 2 cavity and gave it a spin, but I was not very impressed. I got better results with the little brothers, the 311-466 and 311-465. My 30-40 Winchester 1895 shot it OK, but not great.My 06 didn't care for it at all-- groups ran in the 2-3 inch range, half again larger than the 311-644 groups out of that rifle.
However, YMMV, your gun(s) may like it better, You may be a better caster, and your Ideal might be better than my Lyman. Good luck
I am interested in opening a 338 mold to 348 or 350. has anyone ever did anything like this. I don't know how hard it would be to make a cutter to fit the groves in the mold and it could be expanded inside the mold. they make expansion reamers. my idea is to turn a body the size of the inside of the mold and fit it with a cutter that can be forced out by screwing the shank into the body. could be made with opposing cutters. the halves of the mold could be clamped together and the grooves opened up in a milling machine. you would end up with deep grease grooves in the bullet, but if it works it would make a wide variety of molds available for the odd sizes that are expensive and limited. anybody ever try this?
Try Eric at Hollowpoinmolds.com or our own buckshot. Either of those guys can open a mold up for you. Not sure how they'd feel about opening one up that much, but I'm sure it can be done.
I have both the 311466 and 467 both shoot well although not the best groups I have shot.I only lube the bottom two or three grooves.
Tim
Thanks for the info on 467 mold. It will be probably spring before I will have time to work
with it. I always assumed that you filled all the lube grooves, but then you have exposed
lube to pick up dirt and grit, which doesn't sound too good.
Bill
My 311467 works great in the .30/06. I size to .310 and lube three grooves. I've HP'd mine but tend to shoot lighter bullets./beagle
Yep....I kinda like mine too ! !
http://img.photobucket.com/albums/v494/haysb/88.jpg
I had my mold Hp'd by Erik. I can make a medium depth HP , a deep Hp, a flat point like the 311407, a cup point , or a plain based 311467 for plinking all from the same 2 cav. mold.
Here are some photos:
Here is a photo of the flat point pin in position in the mold :
http://img.photobucket.com/albums/v4...P/PICT0009.jpg
Here are flat points that have been cast with ACWW's :
http://img.photobucket.com/albums/v4...P/PICT0006.jpg
Here is the deep HP pin in position , the HP pin extends .450 " deep into the mold cavity :
http://img.photobucket.com/albums/v4...P/PICT0004.jpg
Here are deep HP bullets cast from ACWW's :
http://img.photobucket.com/albums/v4...PICT0004-2.jpg
This photo shows the " Cup Point " HP pin in position :
http://img.photobucket.com/albums/v4...P/PICT0007.jpg
Here are " Cup Point HP Bullets cast from ACWW's ;
http://img.photobucket.com/albums/v4...PICT0009-1.jpg
A close up of the " Cup Point " :
http://img.photobucket.com/albums/v4...P/PICT0008.jpg
I like to shoot my .30 cal. cast bullets sized to .310 ".
I pushed these " nose 1st " through my Lee sizer die that I've honed out to .310".
http://img.photobucket.com/albums/v4...PICT0004-1.jpg
Ben,
Thanks for the excellent post and really great pictures! Mine is a single cav, maybe I'll
HP the mold after I spend some time with the original configuration. Your boolits are very
nice looking, and that is sure a nice group!
Bill
Ben and GLL have the deadly dual-capabilities of: casting beautiful (perfect and shiny) bullets along with taking incredible photographs! They both make me want to buy more moulds!!! [smilie=s:
mtgun44 - That 311467 is one of my wanted moulds. It's a matter of running into one for a good price like you did, because I'm happy with what I've got, but it's good to hear others who keep their eyes peeled run into these now and then. Gives me hope.
Look Fellas,
If I can do it, a cave man can do it.
Ben
You haven't seen how hairy I am and how low my knuckles drag, have you?!? :bigsmyl2:Quote:
Originally Posted by Ben