You bet. Let us know how you make out with it.
Printable View
My collator for 9mm works like a charm, thanks again for all your effort.
I printed another collator for feeding my LEE APP with brass to be deprimed, i run .32S&W Long and printed APP_Brass_Insert_32.stl only to realise that the cases dont fit (i guess it's designed for .32ACP?). Would it be possible to create an insert that works with .32S&W Long?
Just to confirm, the diameter is ok for the case, its the length that is the issue?
The base of the case does not fit the diameter. Hold on, i'll get you a picture and some measurements.
The base diameter measures 0.369in and the case length is 0.911in.
Attachment 286832
Attachment 286833
I've been working on a plate and some other things to be able to collate hollowbase wadcutters, it's not entirely my idea, i just made 3d designs for the concept. It's working pretty well, there are some things that need tweaking. for example the slideplate (for brass) might need adjusting as the bullets sometimes get stuck and pile up. And the .32 dropper needs to be 2.58mm longer to reliably drop the wadcutterbullet and stop the next.
I'd be happy to share the fusion files with you TylerR if you're interested.
https://youtu.be/LnfH-uZsOPo
https://youtu.be/gqGkG7hcpRQ
Attachment 286835
Attachment 286836
Attachment 286834
Sorry took me so long. Very busy. Here is the insert. Please let me know if it works or needs adjustment.
Attachment 286929
It's these: https://www.hn-sport.de/en/reloading...-314-100-gr-hs
(Lead with copper-plating).
It didn’t quite work, needs to come down a bit. My guess is about 0.435in more. And it seems a bit thick, hard to seat it in the holder. When i measure it against my other inserts it’s 0,011in thicker i diameter. So if you could make it around 0,641in diameter, that would probably work.
Thanks again!
I am confused. I made it shorter by 5mm to accommodate the .32SW case, which is a bit less then 24mm long. The formula for the length is 70mm-case length (24mm). Which is 46mm. But you are saying lengthen it by .435in, which would be almost 6mm longer then the original .32acp insert. Something is not making sense.
As far as width, all of the inserts are 16.4mm OD. This new one is the same. I did open the ID to 10.4mm.
Apologies if this has been discussed but I've not found it. How long should the Parts Generator Take? I have made appropriate selections, made sure a Project folder was chosen and pressed play and while it creates a Parts.zip file, it's a 0 byte file and never seems to change. I've waited over an hour more than once, hoping it was a glitch but no joy as of yet. If it's something simple and stupid I should be doing, I'm ok with that, just need to know what "that" is...
When i was using the generator if i checked any the the 3 things i have checked in the pic the generator froze up i had to leave them unchecked and grab the stl's from the main folders manually. i also needed to install openSCAD
Attachment 286959
Trying that right now. About how long should it take to complete?
Using the latest from Github, not sure where the disconnect is but I'll try a few more things. Or quit being lazy and just select them manually... :)
Edit: Handled. Blocked file, which would let it start and run enough to create the initial zip but not write to it after that. :killingpc
Your learned opinions please...
I am looking at adding a Mr. Bullet Feeder to a Dillon 1050 and possibly a Star sizer. If you only needed one unit, would you invest in a 3D set up to make it, or buy the commercial unit? I can get the feeder and point down conversion for less than $600.
I am not a tinkerer. Will be using 125 gr RNFP-158 gr SWC gr .38 cal cast bullets and 122 gr 9mm cast bullets.