Cast Bullet Coating with Epoxy Paint, has any one tried coating their cast bullets with epoxy paint, are there any pros ang cons regarding the coating?
Printable View
Cast Bullet Coating with Epoxy Paint, has any one tried coating their cast bullets with epoxy paint, are there any pros ang cons regarding the coating?
In my experience, epoxy paint is very ridgid / unflexable when dry. I would believe that when the boolit is deformed in the firing process that the epoxy paint would just crack / flake off but I may be wrong....
Robert
Depends on what is embedded with epoxy itself, i.e., colorant. Some work better than others. Need to play with the "lube" like any other. ... felix
I would avoid it.
Have you ever tried to sand epoxy paint?
It drags heavily. You have to change sheets constantly.
The casting goes down the bore, metal to paint contact. Then there is heat and pressure following.
It sounds like a mess about to be made to me.
They used to seal the case to bullet seam with butyrate dope. A very small amount. The dope is nitrocellulose. It burns up with the flame front.
It sealed the case, burned clean.
I might avoid epoxy paint to coat the casting.
here in the philippines there are alot of colored bullet heads they call it teflon coated, but I think it is not teflon but only epoxy paint because it is very hard to scratch by the nails, the thing I noticed , becaused I tried shooting one that has been coated versus the none coated one, I noticed when I cleaned my barrel, my barrel shows no lead deposits compared to the none coated bullet head which shows a lot of lead deposits.
Hope any one could give their insights regarding my findings.. thank you!
The epoxy used on fishing rods when wrapping guides on with thread is flexible. The rod bends, the epoxy bends.
welcome to the board first,
Now, I would love to see some pictures, do any of the suppliers have web sites?
can you get pictures yourself?
I am open to the idea, theory would be the same as jpw or liquid alox I suppose, not a subscriber to the "not invented here, can't possibly work" here.
it seems[to me] it would be pretty hard to control the thickness.
i am thinking he is seeing moly or boron nitride coatings. or even the ny-clad stuff that was banned here.
the purpose is that you have a cleaner barrel to improve accuracy, also I noticed that the barrel is more easier to clean, the coatings on the bullet is localy made, one coat only is applied as I inspect the bullet head and so the thickness has a very minimal change. Today I tried it my self with some epoxy paint and got a desame result with the finished coat... I have to range test the material if I can get a similar result. I also think epoxy paint is elastic..
I read this thread earlier and it got me thinking about Gunkote or Durakote for cast boolit coatings. It's sprayed on and dries very thin. Might get similar results as the old Nyclad ammo. It'd be interesting anyway.
Quote:
Originally Posted by michaelfrancis79 View Post
has any one tried coating their cast bullets with epoxy paint?
What would be the purpose for said coating?
CM
Same question. Why would you want a coating?? Why not just use a jacketed bullet??
What is the purpose?
Shiloh
I noticed while shooting with lead cast bullets, the are lead deposites on the grooves on your barrel after shooting a couple of rounds, in my opinion coating it will reduce the lead deposites on the grooves on your barrel... so thats the main purpose... that why I also need insights regarding the issue. and besides jacketed bullets cost more than cast bullets.
Welcome, if you could post a picture it might help. These boolits that are mode locally, are they loaded or do you load them?
If you're getting leading, you probably have a bullet size issue. This should be corrected first.
I load them
That sounds like either a sizing or alloy.
Instead of lead in the grooves, you might end up with epoxy. Harder to remove.
You need to slug the bore, then add .001, or .002, depending on how it behaves with .001.
I pan lube, run .001 over bore, and get no leading. I push them pretty hot also.
If it don't fit right, you will get skidding. Once a trail is left, more is deposited.
In the beginning, I used to fire a full round of jacketeds when I was wrapping up. Once I found my size, I didn't need to.
It would depend on the texture and strength of the cured epoxy. It might be a good way to get those extra few thousanths that we sometimes need. I am pretty sure that you will not get a clean release on exit so a complete adherence all the way to the target will be needed. Woudl you be able to apply it as a dip to leave the lead tip exposed?
Good luck and have a plan to remove the residue from your failures from the bore and don't get discouraged. New lands are discovered by those who sail out of sight of land.
You have a size issue and possibly an alloy issue. I would also note that the color (pigment) in paint is often made of really abrasive minerals. Dutch Boy used to make some really fine paints using a mineral near me that was known for it's abrasive quality also.
Sounds to me like the epoxy paint might be solving your boolit fit issue more that acting as a lube or jacket.
rfr,
What is in your memory banks about these old Nyclad bullets?
I found a supply(from 80s?) of them the other day I had evidently decided against loading.
Now I'm not sure why I decided that?
CRS is a crippling disease!:roll:
Any information?
Thanks.
PS Still banned? Thought I read something about Federal selling something called nyclad.
??