I found a piece of thick wall 1/2” tubing, pushed a length of 3/8” Delrin into it and secured with a pin peened in place. Easy peasy …
I am also making an adjustable one I’ll show details & pictures of later.
Attachment 297379
Printable View
I found a piece of thick wall 1/2” tubing, pushed a length of 3/8” Delrin into it and secured with a pin peened in place. Easy peasy …
I am also making an adjustable one I’ll show details & pictures of later.
Attachment 297379
Very cool. Still kicking myself for not grabbing one of their microadjust tubes when I had the chance years ago.
Clever ideal, Lefty!!!
I just found a piece of brass tubing the same as the original, only longer, and fit the adjustment slide and set screw to that. I remember I did have to take just a little off the OD of the tubing I bought. As I use it almost exclusively for BP it's a rare occasion I have to change back to the shorter tube.
great idea , sure would be nice to have a bunch of them pre set for different loads
Just picked up a B&M measure. It's a little stiff and only came with a measure made from a 444 brass. Going to try a different spring and need to make a better tube.
Where did you source the brass tube and what is the wall thickness?
Thanks!
The B&M I use most has had its return spring removed totally. I just have to remember to manually return the lever so I don’t drain the reservoir accidentally! :shock:
Mine also has a custom-made drop tube with a Starrett micrometer stem to adjust… gives the ultimate in repeatability. :) I’ll try to dig it out later today and add pix to this post.
Froggie
In preBrandon times, HD and others had, I think, 3/8 aluminum rod and tubing, in 4' lengths. They matched up perfectly One tubing piece was a bit too tight to fit the hopper and needed a little sanding. I went nuts drilling out for thumbscrews on the tube pieces and made a bunch of dimples in the rods. Sharpie colors on the dimples. I made charts to mark out what # tube and what color dimple gave what load in all my powders. Gave up and just have several tubes locked in one place. Gonna try again, someday. I really need dozens of them. I have an original brass tube but don't like changing settings.
I purchased all the reloading gear and a few rifles from the wife of a good friend when he passed, one of these Belding and Mull throwers was in the box and it has two adjustable tubes with it and I have never tried it out. I may give it a try and if it works out I will give my Lyman thrower to nephew. Regards Stephen
They are fantastic and are, almost always, dead on. One problem is getting it mounted solidly.
I thought I had added a picture of the Starrett type drop tube insert. I’ll try again.
A standard drop tube body attaches to the silvery colored collar with a set screw and the shank and brass plug move up and down just like the slide in a “stock” drop tube, but controlled and repeatable with the Starrett thimble.
Froggie
I just use a depth mic to set the tube depth on my B&M. No need to fabricate anything. I have a lathe, so already had the mic. The depth measurement end of calipers would work as well, and just about everyone who reloads has calipers. I record the depth measurement of the tube for each load in my load book.
I made mine because the tube that came with the measure was not big enough for the BP charges I needed to throw. I loaded some BPC's last week and noticed I'd never put the original back together. Still using the one I made 30+ years ago.
I use brass tube from On line metals they sell by the foot lengths. I make the standard slide tubes, thread adjustable in the bleding and mull style and a true micrometer adjust with 3/8 40 threads.
My large capacity bp tube uses a second tube with the bottom end plugged. This tube starts at just under what a fully opened tube throws and goes up from there. Reversing the inner tube gives a normal measure.
1/2" stop collars make a nice base ring and good solid 1/4 20 threads for the thump screw. a length of ready rod makes the stem. JB weld epoxy makes the head. I make either a flat head or a cupped one using a bearing ball to form it.
My B&M has the micrometer adjustable measure. After I have the charge I want for a specific powder, I measure the depth with a dial caliper and record it. I have a chart with dozens of powder/depth settings. It takes about 30 seconds to set the measure for a previously recorded charge. Easy peasy.
Some great ideas for making up a couple tubes. I will definitely be following some of this advice.
Thanks for sharing.
I had the same issues with it moving around. I bolted a piece of wood to the bench and cut an angled slot in it that matches the back of the clamp on the measure. Works great!Attachment 297756Attachment 297757