ADvertise hereTitan ReloadingLee PrecisionStainLess Steel Media
Graf & SonsInline FabricationRotoMetals2

Tab Content
  • M-Tecs's Avatar
    Today, 11:13 AM
    Unless you had a high primer it wasn't a slam fire. Did the primer show a firing pin indent?
    67 replies | 1559 view(s)
  • M-Tecs's Avatar
    Yesterday, 09:34 PM
    What caused the gun to fire?
    67 replies | 1559 view(s)
  • M-Tecs's Avatar
    Yesterday, 08:18 PM
    Easy enough to test with a primed case. Chamber the primed case and pull the charging handle back until the bolt rotates slightly and pull the trigger.
    67 replies | 1559 view(s)
  • Char-Gar's Avatar
    Yesterday, 10:58 AM
    Char-Gar replied to a thread Crisis of faith ? in Our Chapel
    Without a definition of "crisis of faith" that question is impossible to answer.
    4 replies | 79 view(s)
  • M-Tecs's Avatar
    Yesterday, 10:15 AM
    For the folks that believe you can fire an ar out of battery take a primed case and try it. The bolt has to be fully rotated before the firing pin can reach the primer. The video clearly shows and the OP stated he manual cycled the next round...
    67 replies | 1559 view(s)
  • M-Tecs's Avatar
    Yesterday, 09:24 AM
    No with the Dillon swager if you adjust the swager too deep you push material into the bottom of the primer pocket. This seems to only be an issue with 223 due to the small size of the internal support rod.
    67 replies | 1559 view(s)
  • M-Tecs's Avatar
    Yesterday, 01:58 AM
    Great score. I am green with envy.
    34 replies | 793 view(s)
  • M-Tecs's Avatar
    Yesterday, 12:49 AM
    Uncalled for and baseless.
    67 replies | 1559 view(s)
  • M-Tecs's Avatar
    Yesterday, 12:41 AM
    On a side note I was out at the range and a shooter was having lots of failure to cycle/issue. I normally don't stick my nose into other people's business unless asked. I was testing a couple of match ar's This shooter came over and asked...
    67 replies | 1559 view(s)
  • M-Tecs's Avatar
    09-17-2017, 11:45 PM
    In the video the you can't tell if you ejected brass when you manually cycled it but I would bet you did. I am far from an expert on blown AR's but I have inspected and or repaired 9 or 10 that had blown. In addition to building ar service and...
    67 replies | 1559 view(s)
  • Char-Gar's Avatar
    09-17-2017, 03:12 PM
    "And I am convinced that nothing can ever separate us from God's love. Neither death nor life, neither angels nor demons, neither our fears for today nor our worries about tomorrow--not even the powers of hell can separate us from God's love."...
    3 replies | 53 view(s)
  • Char-Gar's Avatar
    09-17-2017, 02:57 PM
    Fever is not an illness in and of itself. It is a symptom of an infection or disorder in the body. Just so a sinful acts is just a symptom of a much larger systemic problem in our beings. We are a people who place self interest and self control over...
    11 replies | 179 view(s)
  • M-Tecs's Avatar
    09-17-2017, 02:10 PM
    M-Tecs replied to a thread M 1 Garands in Military Rifles
    I miss the days of the DCM and $89.00 Garand's. Had my dad qualify but the price went up to $125.00
    9 replies | 260 view(s)
  • M-Tecs's Avatar
    09-17-2017, 01:31 PM
    M-Tecs replied to a thread Dillon 650 Mods in Reloading Equipment
    I have polished mine. With ball powder I can't tell a difference but with stick powder it does improve consistency. Roller bearings and tapering and polishing powder tube are also very beneficial. ...
    10 replies | 246 view(s)
  • M-Tecs's Avatar
    09-17-2017, 01:12 PM
    All primers back out and are reseated by case pressure. Even with zero headspace the primer that was below flush become flush after firing.
    24 replies | 434 view(s)
  • Char-Gar's Avatar
    09-17-2017, 12:28 PM
    God created humankind with free will (the power of choice). We have the ability to stand with God or fall from God. For reasons known only to God, He wanted us to love and follow him by choice, not by compulsion. Without free will there is no real...
    11 replies | 179 view(s)
  • M-Tecs's Avatar
    09-17-2017, 10:33 AM
    Try firing primed cases in a revolver. Most lock up solid due to primer movement.
    24 replies | 434 view(s)
More Activity
About Char-Gar

Basic Information

Date of Birth
July 15, 1942 (75)
About Char-Gar
Location:
Deep South Texas
Interests:
Cast Bullets
Occupation:
Clergy (Retired)

Signature


Disclaimer: The above is not holy writ. It is just my opinion based on my experience and knowledge. Your mileage may vary.

Statistics


Total Posts
Total Posts
11,336
Posts Per Day
2.48
General Information
Last Activity
Today 04:35 PM
Join Date
03-22-2005
Referrals
0

9 Friends

  1. Animal Animal is offline

    Boolit Master

    Animal
  2. bbailey7821 bbailey7821 is offline

    Boolit Master

    bbailey7821
  3. BIG BEAR BIG BEAR is offline

    Boolit Bub

    BIG BEAR
  4. Bob Krack Bob Krack is offline

    Boolit Master at Heavens Range

    Bob Krack
  5. eddymatthews eddymatthews is offline

    Boolit Mold

    eddymatthews
  6. flyer1 flyer1 is offline

    Boolit Master

    flyer1
  7. M-Tecs M-Tecs is offline

    Boolit Master

    M-Tecs
  8. Old School Big Bore Old School Big Bore is offline

    Boolit Master

    Old School Big Bore
  9. StrikerOmalley StrikerOmalley is offline

    Boolit Mold

    StrikerOmalley
Showing Friends 1 to 9 of 9
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check