RotoMetals2Inline FabricationMidSouth Shooters SupplyTitan Reloading
ADvertise hereWidenersLee PrecisionRepackbox

Tab Content
  • NoZombies's Avatar
    03-30-2020, 07:32 PM
    I've got both GC and PB versions of the 225107 molds. I use them in the ladybug and hornet
    9 replies | 350 view(s)
  • NoZombies's Avatar
    03-29-2020, 09:46 PM
    A hydraulic press would make it easier for sure, and you could use set up a system to use the return stroke to eject the formed brass...
    1 replies | 130 view(s)
  • NoZombies's Avatar
    03-28-2020, 07:50 PM
    I was a teenager, the gun was a bronco .22 "bicycle rifle" with a twisting breach. I was holding it choked up and my finger was apparently over the junction between breachface and chamber. It was newly purchased Remington .22 short ammo, the gun had...
    30 replies | 1215 view(s)
  • NoZombies's Avatar
    03-28-2020, 07:46 PM
    In an early catalog, the die parts were labeled in an illustration as parts "H" and "I" and the terms have been used ever since. if someone is selling new dies without the designation, I wouldn't be too concerned. Also RCBS lube-a-matic dies are...
    5 replies | 203 view(s)
  • NoZombies's Avatar
    03-11-2020, 06:29 PM
    If the forum had a like button, I'd click it for this post. Dr Blackmon's dies are very well made, but as Brian said, a very different design than Brian's. I don't own any of either at this point, but I've used both and had excellent results.
    7 replies | 1031 view(s)
  • NoZombies's Avatar
    03-11-2020, 06:27 PM
    random thoughts: If working for maximum consistency, then I run enough to get the dies to temp, (100 or so, depending on design) and then maintain pace until done, with the bullets used to warm things up being used for load development or fouling...
    19 replies | 1841 view(s)
  • NoZombies's Avatar
    03-07-2020, 01:25 AM
    Primer pocket swaging tools, I think some of the punches go to something else. I can't help with the make, mine aren't marked either.
    17 replies | 890 view(s)
  • NoZombies's Avatar
    03-04-2020, 10:00 PM
    I'd like this lot please 35 rounds of brass case 12 ga reloads. They have primer, powder and wad over powder. No shot. Not sure of the powder used but it is likely Black Powder - $25 PM headed your way
    15 replies | 876 view(s)
  • NoZombies's Avatar
    03-03-2020, 08:38 PM
    NoZombies replied to a thread 32 h and r mag. in Cast Boolits
    The RCBS 32--98 SWC did well in mine... As did the Lyman 311008. Actually, mine shot everything well as long as they were no smaller than .313... They were still accurate when smaller in diameter, but they leaded more the smaller they were.
    7 replies | 463 view(s)
No More Results

Statistics


Total Posts
Total Posts
2,314
Posts Per Day
0.58
General Information
Last Activity
Yesterday 06:31 PM
Join Date
05-05-2009
Referrals
2
Home Page
http://nozombies.com
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check