MidSouth Shooters SupplyRotoMetals2WidenersStainLess Steel Media
Lee PrecisionTitan ReloadingInline FabricationGraf & Sons

Tab Content
  • bstone5's Avatar
    Today, 01:25 AM
    I use the Lee factory crimp die to iron out the cases on the 40 S&W. Since I Started using the factory crimp die all assembled ammo passes the plunk test. This die solves a lot of problems with the 40 S&W.
    13 replies | 174 view(s)
  • bstone5's Avatar
    Today, 01:09 AM
    I purchased a second hand Handi-Rifle in 243 for $200.00. The rifle is very good a t 200 yards with a 1.5 inch group with regular jacketed bullets. At the same time I purchased a lever action rifle in 32 Winchester Special. I paid $200.00 for the...
    9 replies | 107 view(s)
  • bstone5's Avatar
    09-16-2018, 01:02 AM
    Most of the M1 barrels need to be bumped up so the sights will be in alignment. This process is not difficult but some care is required so the front sight is in alignment with the receiver. In the Marines we had a jig for changing out barrels on M14...
    16 replies | 761 view(s)
  • bstone5's Avatar
    09-13-2018, 10:06 PM
    A cup is 8 ounces, so 1/2 cup is 4 ounces. So the acetone is easy to measure. What volume measuring container is used to 309 grains of the coating powder. Spoons are parts of cup for the powder? There has to be a volume measure for the...
    21 replies | 1335 view(s)
  • bstone5's Avatar
    09-13-2018, 12:46 AM
    Use 444 Marlin brass for 410 reloading. I use 444?Marlin for making shot she'll for my S&W Govonor pistol. Have reloaded several times wit out needing to resize. There is lot of info on this site on using 444 Marlin brass for shot shells. I got...
    18 replies | 577 view(s)
  • bstone5's Avatar
    09-11-2018, 11:02 PM
    Purchased a Darex many years ago and have sharpened thousands of drill. The Darex model I have has been discontinued and therefore purchased some spare parts when Darex notified me the mode was being discontinued. Still will sharpen by hand when...
    42 replies | 1241 view(s)
  • bstone5's Avatar
    09-07-2018, 09:46 PM
    bstone5 replied to a thread 87 new Marines! in Our Town
    On a cold wet day in November 1965 I graduated on the same parade ground. Thank You for your service.
    26 replies | 651 view(s)
  • bstone5's Avatar
    09-05-2018, 03:33 PM
    A heat gun and a little rubbing with a paper towel, be patient, it will take some time, do not over heat with the heat gun.
    28 replies | 831 view(s)
  • bstone5's Avatar
    09-04-2018, 02:58 PM
    Item #3 arrived in Houston. The package was in good condition, all is good. Thank You bstone5
    33 replies | 2323 view(s)
  • bstone5's Avatar
    09-04-2018, 01:49 AM
    Load the 444 Marlin brass for shot shells for my S&W Govenor. Shoot find. Use 7 1/2 shot with 5 #4 buckshot or just straight 7 1/2 shot. Also shoot a lot of cast bullets in 45 Colt cases, the bullets are powder coated with a home made gas check...
    13 replies | 490 view(s)
  • bstone5's Avatar
    08-29-2018, 09:10 PM
    bstone5 replied to a thread Help in Our Town
    I take Gabapentin for pain in my feet. Without the pills my feet will give me a lot of pain in my feet. Take three a day, the third pill is before I go to sleep. I have no side effects that I can determine but at 73 I often have short memory...
    22 replies | 708 view(s)
  • bstone5's Avatar
    08-28-2018, 10:24 PM
    The Lee factory crimp bie is what I use. The cast bullets are powder coated with a gas check glued on with Locktite. The crimp is very small so as not to damage the powder coating. It takes a while to get the crimp so that it not to deep. Have...
    8 replies | 421 view(s)
  • bstone5's Avatar
    08-27-2018, 11:22 PM
    bstone5 replied to a thread Powder Flask in Muzzleloading.
    I tried to get the same parts and decided it was best to buy a new flask. Went with a different design that had a push rod with a hole thru the rod. This design looked like it would last and with the CVA design does not have the bent spring that...
    7 replies | 379 view(s)
  • bstone5's Avatar
    08-27-2018, 06:49 PM
    I will take #3 H&R stock for rifle. Will PM with regard to total cost including shipping and Pay Pal address. bstone5
    33 replies | 2323 view(s)
  • bstone5's Avatar
    08-27-2018, 06:41 PM
    I will take #3 H&R stock for rifle. Will PM with regard to total cost including shipping and Pay Pal address. bstone5
    33 replies | 2323 view(s)
  • bstone5's Avatar
    08-25-2018, 11:48 PM
    Automated my Master Caster several years ago. Went with the Hatch control method with the air cylinder in the back, the controls and air cylinder work very well. I had to get a good air dryer since the air control valves will not operate properly...
    9 replies | 492 view(s)
No More Results
About bstone5

Basic Information

About bstone5
Biography:
Reload Target Shooting
Location:
Houston TX
Interests:
Building Target Rifles
Occupation:
Retired At 70 Years Old

Statistics


Total Posts
Total Posts
750
Posts Per Day
0.22
General Information
Last Activity
Today 01:41 AM
Join Date
04-22-2009
Referrals
1

1 Friend

  1. Tom_Highway Tom_Highway is offline

    Boolit Bub

    Tom_Highway
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check