RotoMetals2RepackboxLee PrecisionInline Fabrication
Titan ReloadingMidSouth Shooters SupplyADvertise here

Donate Now Goal amount for this year: 6000 USD, Received: 6135 USD (102%)
OUR GOAL HAS BEEN MET!
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


Tab Content
  • randyrat's Avatar
    09-10-2019, 06:32 AM
    Check this link out http://www.gmdr.com/lever/lowveldata.htm
    21 replies | 646 view(s)
  • masscaster's Avatar
    09-03-2019, 12:44 PM
    Hi curator, That minie was designed for the .58 Kentucky style pistols. I have the mould and shot it in a .58 Zouave with moderate success. The skirt is quite thin and will blow out with heavier loads. Start out on the lower end of the charge and...
    6 replies | 234 view(s)
  • masscaster's Avatar
    08-31-2019, 02:11 PM
    Hi Bill, I cast the Lyman #457483 GC (listed @ 378 gr. Lyman #2. 395 gr. my alloy) for loads out to 300 yards, and Lyman #457406 GC (listed 480 gr. #2. 485 - 500 gr. my alloy) for 300 - 500 yards. These are for Smokeless of course. The heavier...
    5 replies | 267 view(s)
  • masscaster's Avatar
    08-30-2019, 12:21 PM
    I would do a more local search for Babbit. Surely there's bearing companies around. Places that rebuild car engines will probably have old crank bearings in a tub. Jeff
    11 replies | 872 view(s)
  • masscaster's Avatar
    08-29-2019, 01:28 AM
    For one, the raised edge will help square up the gas check. Secondly, the die has a throat and the lip will have the most force on the outer edge of the check. The GC should always seat tight to the base of the boolit. All my old Lyman dies are...
    13 replies | 513 view(s)
  • masscaster's Avatar
    08-28-2019, 12:12 PM
    I always used Baking Soda and water. Mix it until it's a murky water, use a few patches with it, then some clean patches. Follow this up with a couple patches of Marvel Mystery Oil. I also use this oil as a whole wipe down, leaving a light film....
    44 replies | 1624 view(s)
  • masscaster's Avatar
    08-28-2019, 11:58 AM
    The raised edge is for aid in seating Gas Checks.
    13 replies | 513 view(s)
  • masscaster's Avatar
    08-22-2019, 11:20 AM
    HI Life Member, I can cast a .645 RB. Check your Bore size, as you might be able to use a raw ball and over powder wad or a paper patched. It could possibly be large enough with this ball to use some ticking. PM me if you want, i log in...
    3 replies | 269 view(s)
No More Results
About stubshaft

Basic Information

About stubshaft
Location:
Southernmost State of the Union
Occupation:
National Fisheries

Signature


If God didn't want man to eat animals, he wouldn't have made them out of MEAT!

The last thing I want to do is hurt you. But it's still on my list.

Statistics


Total Posts
Total Posts
4,189
Posts Per Day
1.10
General Information
Last Activity
08-25-2019 01:09 AM
Join Date
04-09-2009
Referrals
2

10 Friends

  1. 10 Spot Terminator 10 Spot Terminator is offline

    Boolit Bub

    10 Spot Terminator
  2. BobMac51 BobMac51 is offline

    Boolit Mold

    BobMac51
  3. frankenfab frankenfab is offline

    Boolit Master

    frankenfab
  4. Idaho Sharpshooter Idaho Sharpshooter is offline

    Boolit Master

    Idaho Sharpshooter
  5. ilikec2 ilikec2 is offline

    Boolit Mold

    ilikec2
  6. jameslovesjammie jameslovesjammie is offline

    Boolit Master

    jameslovesjammie
  7. jdgabbard jdgabbard is offline

    Boolit Master

    • Send a message via Yahoo to jdgabbard
    jdgabbard
  8. madcaster madcaster is offline

    Boolit Master in Heaven's Range

    madcaster
  9. masscaster masscaster is offline

    Boolit Buddy

    masscaster
  10. randyrat randyrat is offline

    Boolit Master

    randyrat
Showing Friends 1 to 10 of 10
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check