StainLess Steel MediaRotoMetals2Lee PrecisionInline Fabrication
MidSouth Shooters SupplyTitan ReloadingADvertise hereGraf & Sons

Tab Content
  • bkbville's Avatar
    04-16-2018, 12:53 PM
    bkbville replied to a thread Faulty Lee pot? in Casting Equipment
    You'd need a 600W dimmer, but I don't see how you'll benefit, as you would still have open loop temperature control. A PID (closed loop control) is a better way to maintain and control temperature. Using a PID I would simply bypass the...
    19 replies | 570 view(s)
  • bkbville's Avatar
    04-16-2018, 12:46 PM
    I've seen both the heating element and the temp switch on Midway... other than that not much to go wrong with a pot that isn't over heated or placed somewhere rusty. It's a bargain - simply does the job
    12 replies | 454 view(s)
  • bkbville's Avatar
    04-16-2018, 12:39 PM
    I'd like to see an actual scientific study done on this - I've been skeptical about wearing out muzzles from cleaning rods and such when they are softer, generally much softer, than the barrel steel... Wearing off muzzle steel from a bronze brush,...
    40 replies | 1112 view(s)
  • bkbville's Avatar
    04-16-2018, 12:19 PM
    Its good to question what we "know"... there is a lot of good knowledge that comes from old-wives tales and other hand me down knowledge, but some of it is, of course, poppycock.
    34 replies | 831 view(s)
  • bkbville's Avatar
    04-12-2018, 11:53 AM
    I make a concoction of the heart of a toad, eye of a newt, seaweed, hair of border collie, scraping of ox-hoof, and ground eel spine, boiled in the darkest swamp water you can find, simmered, and reduced to a paste I then take the paste, throw it...
    49 replies | 2301 view(s)
  • bkbville's Avatar
    04-12-2018, 11:44 AM
    Unless you're only looking for prototyping the wads,(and then having them made using injection molding for example) I think you'll be disappointed in current 3D printing technology for printing wads. Printing 3D is slow, and a bit imprecise in...
    15 replies | 417 view(s)
  • bkbville's Avatar
    04-05-2018, 09:37 PM
    Pits or chamber scratch is most likely the cause.
    37 replies | 1733 view(s)
  • bkbville's Avatar
    04-03-2018, 11:07 PM
    Very NICE!... and very interested... Could you post more detail - maybe pictures - of your prepared cartridges? Particularly interested in your case length, OAL, and how you seat them, and if you crimp them. I've been forming from 8mm...
    6 replies | 458 view(s)
  • bkbville's Avatar
    04-01-2018, 10:37 AM
    You may want to consider a post-war if your looking for a shooter. I have a plainfield that I can shoot without worrying about collector value, and a WWII model that sits in the bank... uh... safe.
    27 replies | 960 view(s)
No More Results
About bkbville

Basic Information

Statistics


Total Posts
Total Posts
241
Posts Per Day
0.07
General Information
Last Activity
Yesterday 12:30 PM
Join Date
03-29-2009
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check