RepackboxRotoMetals2Titan ReloadingLee Precision
ADvertise hereInline FabricationWidenersMidSouth Shooters Supply

Tab Content
  • Maven's Avatar
    06-04-2020, 06:59 PM
    6pt-, Sometimes it is less than 3 weeks. My last one, a .618" RB for my 20ga. trade gun, arrived in ~2 weeks and cast exactly at the dimension I asked for (.618").
    22 replies | 548 view(s)
  • Maven's Avatar
    06-04-2020, 12:29 PM
    All, The new, blue/gray labeled plastic containers are Goex. Here's a cut & paste from Graf's: Product Information As of 2019, Manufactured for Graf & Sons by Goex Powder Inc. While Goex has improved manufacturing processes and material...
    20 replies | 482 view(s)
  • Maven's Avatar
    06-04-2020, 09:07 AM
    I'll soon need to place a BP order and was wondering about the new Goex BP produced for Graf & Sons*. Any pros? cons? Thanks in advance! *previously produced by Wano (green label; red, white & blue "Schuetzen" label).
    20 replies | 482 view(s)
  • Maven's Avatar
    06-04-2020, 08:55 AM
    6pt-, I have several Tanner RB moulds and highly recommend them. Fit & finish are excellent, use standard handles (e.g., I use RCBS), and they cast to your specification. Priced right too!
    22 replies | 548 view(s)
  • Maven's Avatar
    05-30-2020, 10:06 AM
    gw, "H" and "I" are taken from illustrations of the older Ideal lube sizing machines, #1 and #45. Both are shown in the Lyman "Cast Bullet Handbook, 3rd Ed.", pp. 34 and 41 respectively.
    8 replies | 508 view(s)
  • Maven's Avatar
    05-25-2020, 09:00 AM
    John, Dutch is alive and well and often writes as Dr5x on the ML Forum.
    12 replies | 1006 view(s)
  • Maven's Avatar
    05-24-2020, 09:16 AM
    Thanks, EMC! (I was very pleased with that target as I hadn't fired the SBH in ~6 months.)
    3 replies | 325 view(s)
  • Maven's Avatar
    05-23-2020, 12:50 PM
    Maven replied to a thread .45 cal. Patch Size? in Muzzleloading.
    This may sound stupid, but I once averaged all the patch diameter/size dimensions I read about in a thread on another forum. It came out to 2.3 x RB diameter. In the case of Greg's .445" RB, that would be 1.02" or 1". Btw, I've using this...
    16 replies | 938 view(s)
  • Maven's Avatar
    05-23-2020, 12:45 PM
    I have a .445 cal mold and am prepared to buy a .440 if needed. Greg, A quick & dirty test (with an empty gun!) is to see whether a bare .445" RB will roll all the way down the barrel and out again. If it does, you'll just have to see which...
    12 replies | 1006 view(s)
  • Maven's Avatar
    05-22-2020, 11:52 AM
    Here is a photo of Tuesday's range session with #429260 over 8gr. Unique. The WC was sized to .431", lubed with Lar's Xlox, and taper crimped. I fired these @ 25 yd. with the the SBH's butt on a "rabbit ear" bag. I think if I used a 1" red...
    3 replies | 325 view(s)
  • Maven's Avatar
    05-22-2020, 11:31 AM
    Try googling Bill Ferguson, "The Antimony Man" for ideas about incorporating antimony into your WW mixture. Btw, Ferguson used to sell antimony + a special flux which allowed alloying it at 600 deg. - 700 deg. temperatures.
    14 replies | 486 view(s)
  • Maven's Avatar
    05-14-2020, 06:12 PM
    Maven replied to a thread 8x57 boolits? in Military Rifles
    Just for you, 444ttd:
    10 replies | 509 view(s)
  • Maven's Avatar
    05-12-2020, 03:53 PM
    Lead collector, At one time I owned 2 K-31's (since sold), and found some of the CB's you mentioned above were quite accurate: Ly. #311466, Ly. #311291, and the Lee CB were favorites. However, I sized them to .309" and needed a nose reducing die*...
    31 replies | 1703 view(s)
  • Maven's Avatar
    05-08-2020, 03:25 PM
    msm, I had the same cap ignition problem that you have. To wit, it usually took 2 strikes to fire the caps with either the factory nipples or the Uncle Mike's I replaced them with. The Uncle Mike's were no better than the originals. Because the...
    53 replies | 3665 view(s)
  • Maven's Avatar
    05-07-2020, 09:32 AM
    Jake, I use a C.E. Harris designed, NOE produced ~160gr. GC CB, which I size to .316" for my SKS: Very accurate and easy to cast from my 6 cavity mould.
    20 replies | 862 view(s)
No More Results
About Finn45

Basic Information

About Finn45


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
10-08-2019 02:33 AM
Join Date

3 Friends

  1. Frank46 Frank46 is offline

    Boolit Master

  2. Jumptrap Jumptrap is offline

    Boolit Buddy

  3. Maven Maven is offline

    Boolit Master

Showing Friends 1 to 3 of 3
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check