Titan ReloadingWidenersMidSouth Shooters SupplyRepackbox
Inline FabricationRotoMetals2Lee PrecisionADvertise here

Tab Content
  • Maven's Avatar
    Today, 09:16 AM
    Thanks, EMC! (I was very pleased with that target as I hadn't fired the SBH in ~6 months.)
    3 replies | 210 view(s)
  • Maven's Avatar
    Yesterday, 12:50 PM
    Maven replied to a thread .45 cal. Patch Size? in Muzzleloading.
    This may sound stupid, but I once averaged all the patch diameter/size dimensions I read about in a thread on another forum. It came out to 2.3 x RB diameter. In the case of Greg's .445" RB, that would be 1.02" or 1". Btw, I've using this...
    15 replies | 200 view(s)
  • Maven's Avatar
    Yesterday, 12:45 PM
    I have a .445 cal mold and am prepared to buy a .440 if needed. Greg, A quick & dirty test (with an empty gun!) is to see whether a bare .445" RB will roll all the way down the barrel and out again. If it does, you'll just have to see which...
    8 replies | 168 view(s)
  • Maven's Avatar
    05-22-2020, 11:52 AM
    Here is a photo of Tuesday's range session with #429260 over 8gr. Unique. The WC was sized to .431", lubed with Lar's Xlox, and taper crimped. I fired these @ 25 yd. with the the SBH's butt on a "rabbit ear" bag. I think if I used a 1" red...
    3 replies | 210 view(s)
  • Maven's Avatar
    05-22-2020, 11:31 AM
    Try googling Bill Ferguson, "The Antimony Man" for ideas about incorporating antimony into your WW mixture. Btw, Ferguson used to sell antimony + a special flux which allowed alloying it at 600 deg. - 700 deg. temperatures.
    14 replies | 393 view(s)
  • Maven's Avatar
    05-14-2020, 06:12 PM
    Maven replied to a thread 8x57 boolits? in Military Rifles
    Just for you, 444ttd: https://www.artfulbullet.com/index.php?threads/for-waco-two-lee-8mm-cbs.6270/
    10 replies | 434 view(s)
  • Maven's Avatar
    05-12-2020, 03:53 PM
    Lead collector, At one time I owned 2 K-31's (since sold), and found some of the CB's you mentioned above were quite accurate: Ly. #311466, Ly. #311291, and the Lee CB were favorites. However, I sized them to .309" and needed a nose reducing die*...
    25 replies | 586 view(s)
  • Maven's Avatar
    05-08-2020, 03:25 PM
    msm, I had the same cap ignition problem that you have. To wit, it usually took 2 strikes to fire the caps with either the factory nipples or the Uncle Mike's I replaced them with. The Uncle Mike's were no better than the originals. Because the...
    34 replies | 2243 view(s)
  • Maven's Avatar
    05-07-2020, 09:32 AM
    Jake, I use a C.E. Harris designed, NOE produced ~160gr. GC CB, which I size to .316" for my SKS: Very accurate and easy to cast from my 6 cavity mould.
    20 replies | 676 view(s)
  • Maven's Avatar
    05-06-2020, 06:38 PM
    Maven replied to a thread Belevue in Muzzleloading.
    Try this, big ted: https://www.muzzleloadingforum.com/threads/new-website-for-black-powder-shooters.120345/
    8 replies | 974 view(s)
  • Maven's Avatar
    05-05-2020, 03:37 PM
    As per Ken's (Pressman) suggestion, I'm posting a brief description of my historic mould. I picked up the pictured B & M Iron #429260 (wadcutter)* on eBay years ago for a very good price. It was filthy, but not abused and cleaned up nicely, so much...
    3 replies | 210 view(s)
  • Maven's Avatar
    05-04-2020, 12:59 PM
    Maven replied to a thread Belevue in Muzzleloading.
    I really like his work, both written and video.
    8 replies | 974 view(s)
  • Maven's Avatar
    04-30-2020, 09:30 AM
    You can if you first fill all the grooves with your favorite CB lube. However, it does require a bit of muscle, and unless you have a exceptional well-fitted top punch, you risk distorting the bullet nose. Sizing to .311" and the to .309" is more...
    13 replies | 1156 view(s)
  • Maven's Avatar
    04-30-2020, 09:23 AM
    Yes, it does work quite well, but you may want/need to lube the CB's first to prevent them sticking in the die. This has happened to me several times and it required a propane torch to melt them out, then dropping the die into ATF. Needless to...
    7 replies | 1259 view(s)
  • Maven's Avatar
    04-25-2020, 08:39 AM
    Maven replied to a thread Sizing for Marlin 336 in Cast Boolits
    KevH, I tried sizing CB's from .309" - .311", but found the #336 (Microgroove rifling) was most accurate with CB's sized to .310". Moreover, my gun was especially accurate with Ly. #311466 and Saeco #315.
    12 replies | 458 view(s)
No More Results
About Finn45

Basic Information

Age
54
About Finn45
Location:
Finland

Statistics


Total Posts
Total Posts
302
Posts Per Day
0.05
General Information
Last Activity
10-08-2019 02:33 AM
Join Date
03-17-2005
Referrals
1

3 Friends

  1. Frank46 Frank46 is offline

    Boolit Master

    Frank46
  2. Jumptrap Jumptrap is offline

    Boolit Buddy

    Jumptrap
  3. Maven Maven is offline

    Boolit Master

    Maven
Showing Friends 1 to 3 of 3
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check