MidSouth Shooters SupplyADvertise hereRotoMetals2Lee Precision
Inline FabricationTitan ReloadingGraf & SonsStainLess Steel Media

  • marlinman93's Avatar
    07-11-2018, 11:30 AM
    I've had good results with 2400 in the .32-20WCF. RCBS Cast Bullet manual lists 10.0 grs. of 2400 for 1537 fps, but I started down around 8.0 grs. because I am not a high speed fan. I like the 8.0 grs. of 2400 load with a 115 gr. bullet a lot.
    14 replies | 255 view(s)
  • marlinman93's Avatar
    07-10-2018, 04:43 PM
    Based on this info, I'd do as mentioned and simply use your sizing die to lightly compress the case necks after loading.
    14 replies | 255 view(s)
  • M-Tecs's Avatar
    07-10-2018, 01:38 AM
    This is from another site: I contacted CCI back a couple years ago and asked to speak to their primer tech. I was connected with a wonderful woman who had worked there for 37 years. I asked her the following, "What is the difference between your...
    26 replies | 729 view(s)
  • marlinman93's Avatar
    07-09-2018, 01:40 PM
    I don't crimp much since most of my loads are for single shots also. But I have found that certain calibers and guns I own shoot better with a crimp. So I never rule it out until I'm done finding the best load for a gun.
    14 replies | 255 view(s)
  • marlinman93's Avatar
    07-09-2018, 01:02 PM
    I've always used muzzleloader round balls to slug bores, and how big isn't all that important. I keep two boxes of them on the bench in .45 and .38 calibers. Once I use a ball and have measured it, I toss it back in the box to use again on a smaller...
    8 replies | 336 view(s)
  • marlinman93's Avatar
    07-06-2018, 11:08 AM
    Small world. Larry who is seen shooting the 990 yd. dinger at our long range shoot last year is a friend of mine! That's also a .40-65 that Larry is shooting, but a pistol grip stock. It's a Green Mountain barrel also, like mine. My friend Steve is...
    7 replies | 399 view(s)
  • M-Tecs's Avatar
    07-06-2018, 04:31 AM
    Very nice work.
    7 replies | 399 view(s)
  • marlinman93's Avatar
    07-05-2018, 06:44 PM
    Yes, it went to the East Coast. Then to the Dakotas. And finally to my friend in Indiana, before finding it's way home to me! Had a bit of a tough life until my friend bought it. It came to him with the stock broken and tangs bent! Also had the...
    7 replies | 399 view(s)
  • marlinman93's Avatar
    07-05-2018, 02:54 PM
    A number of years ago I wanted to build up a Rolling Block for long range shooting. I decided it would be a .40-65 Win. chamber, and began looking for an action. My friend the late Whitey Hanson had an original receiver, and after some swapping I...
    7 replies | 399 view(s)
  • marlinman93's Avatar
    07-05-2018, 11:33 AM
    A lot of what's been said here is true, but it's nothing new either. Some seem to think this corporate mentality is a new thing, but it's existed since factories existed! Winchester bought numerous companies and then simply closed them down. Had it...
    30 replies | 1121 view(s)
  • marlinman93's Avatar
    07-04-2018, 02:04 PM
    I use .32 Win. Spl. when I don't have original .32-40 brass.
    13 replies | 391 view(s)
  • M-Tecs's Avatar
    07-03-2018, 03:04 PM
    M-Tecs replied to a thread S&W Model 14 soured in Cast Boolits
    Don't know if the effects of this would be that severe but when the firing pin springs of a rifle get weak groups open way up.
    60 replies | 2847 view(s)
  • M-Tecs's Avatar
    07-03-2018, 02:12 AM
    M-Tecs replied to a thread What drill sizes? in Our Town
    https://www.shotgunworld.com/bbs/cpg1410/albums/userpics/33132/prmrtble.jpg
    22 replies | 14202 view(s)
  • M-Tecs's Avatar
    07-02-2018, 05:10 PM
    Creedmoor use to sell them. Them may be able to help. https://www.creedmoorsports.com/
    9 replies | 453 view(s)
  • M-Tecs's Avatar
    07-02-2018, 03:45 PM
    Not sure but I don't think they are still available http://www.accurateshooter.com/optics/microsight-technology-for-iron-sights/
    9 replies | 453 view(s)
  • M-Tecs's Avatar
    07-01-2018, 08:00 PM
    For open areas for self defense or hunting coyotes an AR is hard to beat. I call a lot of coyotes and shotguns have there place but range is the limiting factor. If you are not calling shotguns are basically useless for coyotes in open areas.
    18 replies | 654 view(s)
  • M-Tecs's Avatar
    06-25-2018, 11:25 PM
    http://www.trapdoorcollector.com/cgi-bin/afrasca/bulletin/config.pl?read=34505 "The sight was designed by the same man who designed the 1901 Krag rear sight and the 1905 rear sight on the 1903 Springfield. They are Excellent sights that when...
    2 replies | 173 view(s)
  • M-Tecs's Avatar
    06-22-2018, 07:43 PM
    On the new SS one that my friend has I can't real comment. He has only shot it on a limited basis and he has never real rung it out for accuracy.
    8 replies | 651 view(s)
  • M-Tecs's Avatar
    06-22-2018, 07:37 PM
    I am looking for and adjustable rear sight for an HD. If that is one of the items you have as a spare maybe we can work something out. http://www.histandard.info/manuals/ord/ http://www.histandard.info/
    8 replies | 392 view(s)
  • M-Tecs's Avatar
    06-22-2018, 02:19 AM
    A friend has a SS one. Finish isn't as nice as my blued Monson's but machining is better.
    8 replies | 651 view(s)
  • marlinman93's Avatar
    06-18-2018, 08:44 PM
    Since the base band is the one that seals the bore, I've reamed out the base band on several molds to make them seal in the bore better. Opening up just the base band will get you where you need to be, and often avoid chambering issues too. I have...
    21 replies | 871 view(s)
  • marlinman93's Avatar
    06-18-2018, 06:05 PM
    Yes MVA is offering complete finished receivers, plus all parts for a High Wall. I've purchased parts from them and both price and workmanship are great! http://montanavintagearms.com/winchester-parts/
    40 replies | 1132 view(s)
  • marlinman93's Avatar
    06-18-2018, 11:32 AM
    MVA sells all the High Wall parts you'd need new. So changing calibers isn't an issue and you could simply set your extractor aside with the original barrel if rebarreling.
    40 replies | 1132 view(s)
  • marlinman93's Avatar
    06-17-2018, 03:58 PM
    I'd second the .40-65, but only if the existing bore isn't so bad that it would not clean up to be a .40-65 caliber. If it wont clean up then I'd consider going back to .38-55 caliber. A favorite of mine, and one of the great old calibers.
    40 replies | 1132 view(s)
More Activity
About marlinman93

Basic Information

About marlinman93
Location:
Oregon
Interests:
Singleshots and pre WWI MArlins

Statistics


Total Posts
Total Posts
1,197
Posts Per Day
0.35
General Information
Last Activity
07-13-2018 01:07 PM
Join Date
03-08-2009
Referrals
0

1 Friend

  1. M-Tecs M-Tecs is offline

    Boolit Master

    M-Tecs
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check