RotoMetals2Titan ReloadingRepackboxLee Precision
MidSouth Shooters SupplyADvertise hereInline FabricationWideners

Tab Content
  • ole_270's Avatar
    07-07-2019, 10:07 AM
    Back in my machine shop days calipers were outlawed for anything under .005" tolerance. I've seen some of the cheaper mics test out fine near zero, but be off as much as .002" near the center of the travel. buyer beware
    33 replies | 728 view(s)
  • ole_270's Avatar
    07-07-2019, 09:56 AM
    For the loads I run the most I tend to use softer alloys. I've had no trouble with 12 Bhn up to 1600 fps. The only thing I quench is 308 loads over 2000 fps. These are a 1.4%Sn, 2.9%Sb alloy and get quenched when they come out of the PC oven and are...
    61 replies | 1672 view(s)
  • ole_270's Avatar
    07-03-2019, 11:38 PM
    I use a bit of dacron between 21 gr 4198 and a 250 gr cast bullet, not tamped down just get it started and let the bullet place it as it's seated. It's the most accurate load I've found so far. I don't use a filler with my plinking load of 10 gr...
    10 replies | 344 view(s)
  • ole_270's Avatar
    06-30-2019, 10:06 PM
    Not an ar but I've been playing with an old JC Higgins M51-L in 308. Bore and throat are fairly large. I've pretty much settled on the Saeco #315 clone by NOE, sized to .3115, to be able to partially fill and bridge the throat. I'm using PC,...
    4 replies | 480 view(s)
  • ole_270's Avatar
    06-21-2019, 09:31 PM
    I have the Lee #68 clone in a 2 holer and the 200RF in a 6. Doug Guy throated the barrel of my Sig so it handles either loaded out as far as the magazines will take them. I've only had a feeding problem when I goofed and left the case mouth too...
    21 replies | 680 view(s)
  • ole_270's Avatar
    06-21-2019, 08:58 PM
    Thanks guys, got the sheets app and it's working. just have to add all my custom alloys and learn some of the workings of the android app.
    5 replies | 222 view(s)
  • ole_270's Avatar
    06-21-2019, 03:21 PM
    The Hancom office viewer isn't enough?
    5 replies | 222 view(s)
  • ole_270's Avatar
    06-21-2019, 09:55 AM
    Guys I've been using Bumpy's calculator for several years on my desktop and really like it. Problem is when I download it for my new Android tablet for portable use. The yellow columns are locked, or at least haven't figured out how to make...
    5 replies | 222 view(s)
  • ole_270's Avatar
    06-18-2019, 08:38 AM
    I use the NOE system with very good success. The only problem I have with it is that since it screws into the press from the bottom, the bushing is too low in the cycle making the action outside of the power stroke. Some harder or larger boolets...
    18 replies | 795 view(s)
No More Results
About ole_270

Basic Information

About ole_270
Location:
SE Ks
Interests:
shooting/hunting
Occupation:
Engineer/CNC Programmer

Statistics


Total Posts
Total Posts
209
Posts Per Day
0.06
General Information
Last Activity
Today 02:28 PM
Join Date
03-02-2009
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check