RotoMetals2ADvertise hereInline FabricationWideners
Titan ReloadingRepackboxMidSouth Shooters SupplyLee Precision

Tab Content
  • ole_270's Avatar
    11-14-2019, 12:17 AM
    Calipers won't be all that accurate for the id measurement. My JES slugs at .3755. I load the Starline 2.082 length brass with Accurate mold 375-250B sized .377. Shoots great.
    6 replies | 278 view(s)
  • ole_270's Avatar
    11-12-2019, 07:00 PM
    Wish I had pictures of the last deer I shot with the 38-55. 38-250B mold from Accurate, running 1600 fps. That big flat point at 30 yards makes quite an impression. Doe was stumbling at the 3rd jump and down in 20 yards. There was a bit more...
    29 replies | 2079 view(s)
  • ole_270's Avatar
    11-12-2019, 11:17 AM
    Pretty much
    21 replies | 629 view(s)
  • ole_270's Avatar
    11-11-2019, 10:20 PM
    Nice to see another lever with open irons being used in the field. Also nice to see you posting, I've been missing your hunting pictures over on the fire.
    21 replies | 629 view(s)
  • ole_270's Avatar
    11-10-2019, 09:43 PM
    Get you some 75 gr hp or plastic tipped for varminting and to use up that 4895. Works great in my ruger. I much prefer the H4350 for 100+ though.
    24 replies | 976 view(s)
  • ole_270's Avatar
    11-10-2019, 09:32 PM
    ole_270 replied to a thread Too dumb to kill in Hunting with CB's
    Had a pair of fawns that liked to bed in the back yard last year. They'd stay most of the day and towards evening mom would show up to check on them and feed them. One day I was sighting in a rifle on my backyard range. The sight path is along one...
    38 replies | 1822 view(s)
  • ole_270's Avatar
    11-08-2019, 03:46 PM
    The older I get the more I enjoy hunting with these old guns and cartridges. My rifle isn't that old, but the 38-55 chambering is. Works great at woods ranges.
    33 replies | 1098 view(s)
  • ole_270's Avatar
    11-06-2019, 06:48 PM
    I`ve come to prefer the gutless method. Skin in sections and quarter where it lays or wherever you prefer if you don't want to do it in the hunting area. Pack the quarters out and put them in a cooler. I usually run water over it and drain off a...
    43 replies | 1166 view(s)
  • ole_270's Avatar
    11-01-2019, 08:01 PM
    I use the NOE version of the Saeco #315 in my 308 for faster loads. In my European o/s throat and bore I size .312 and seat into the lands. 34 gr Norma 202 gets me 2040 fps, 35-Varget gets 2050, and 44-H4350 gets 2270. For lighter loads I use the...
    15 replies | 557 view(s)
  • ole_270's Avatar
    10-31-2019, 12:09 PM
    I've got about 50 lbs of ingots given to me by a co-worker before I retired. He said they were WW he and his dad had gathered when he was a kid, I'd guess sometime in the 60's. They are marked WW. Now his dad also ran a print shop so there is the...
    10 replies | 677 view(s)
  • ole_270's Avatar
    10-22-2019, 09:04 AM
    Babbitt can be most anything, my old Machinery Handbook has about two pages of tables of differing alloys ranging from 90 some % lead to near pure tin. I picked up quite a bit one time that was stamped #4, hoped it was SAE #4 which is mostly tin....
    8 replies | 565 view(s)
  • ole_270's Avatar
    10-21-2019, 09:50 AM
    The range lead I've been digging out has a little higher concentration of cast bullets in it, been averaging 0.2% Sn, 1.5% Sb according to BNE's testing. I generally add some tin to give more diameter in some molds for some applications.
    13 replies | 688 view(s)
  • ole_270's Avatar
    10-20-2019, 09:41 PM
    I cast that 280473 spitzer about 25 years ago for use in my 270. I used loads from the Lyman manuals, but never got it to shoot very well above 1500 fps. I ended up using it with Red Dot at around 3.5 grains for offhand practice loads. I've since...
    23 replies | 728 view(s)
  • ole_270's Avatar
    10-20-2019, 10:41 AM
    ole_270 replied to a thread bullet for 25/20 in Cast Boolits
    Anyone looking for a mold for the 25-20 should check out the NOE 260283, I have it in a plainbase version and it's about all I shoot anymore. The Lyman 257420 I have always worked well, just wanted to do away with the gas check.
    8 replies | 414 view(s)
  • ole_270's Avatar
    10-20-2019, 10:32 AM
    Son took his first muzzleloader deer this year, He's close to 40 and has taken everything from prairie dogs to elk with modern centerfires. Used my old TC New Englander 50 cal with 777 and the smaller of the two Lee REAL conicals (210?). Buck made...
    23 replies | 895 view(s)
No More Results
About ole_270

Basic Information

About ole_270
Location:
SE Ks
Interests:
shooting/hunting
Occupation:
Engineer/CNC Programmer

Statistics


Total Posts
Total Posts
246
Posts Per Day
0.06
General Information
Last Activity
Today 11:05 AM
Join Date
03-02-2009
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check