RepackboxInline FabricationTitan ReloadingLee Precision
ADvertise hereMidSouth Shooters SupplyWidenersRotoMetals2

Donate Now Goal amount for this year: 6000 USD, Received: 3655 USD (61%)
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****

  • barrabruce's Avatar
    08-02-2020, 11:23 PM
    Well finally got some p5 bearings from *** in Germany. I had manicured the spindle pretty good with the old bearings for fit as well as everything else. I had a sleeve made out of bronze for the non obtainable bearing seal to fit a normal stock...
    32 replies | 1688 view(s)
  • barrabruce's Avatar
    07-27-2020, 08:21 PM
    Someone loaned me an ultrasonic cleaner. It did work o.k. The High pitched buzzy noise got in and really rung my ears and drove me insane. I thanked him for the loan Maybe they don’t all sound like that but I won’t be running out buying...
    17 replies | 574 view(s)
  • barrabruce's Avatar
    07-17-2020, 03:31 AM
    No I think you are right. I got a good size seal to go I the bush with the groove. Apparently it is a feature of these lathes they leak or they don’t. There is a small area between the chamfer on the inside of he bearing race and the key groove...
    32 replies | 1688 view(s)
  • barrabruce's Avatar
    07-16-2020, 02:11 PM
    This shows the position roughly where it will be with the gear spacer must have a gap to provide take up and preload. There is a very fine surface on the sleeve and bearing to provide a seal. The other side has grub screws to provide pressure to...
    32 replies | 1688 view(s)
  • barrabruce's Avatar
    07-16-2020, 01:14 PM
    Is it supposed to seal on the yellow machined faces. It would make sense then. The bearings are the same but the seals are slightly different size. Thnx
    32 replies | 1688 view(s)
  • barrabruce's Avatar
    07-16-2020, 05:25 AM
    Well here is something different. I can’t see how this is supposed to seal the oil in. One side of the bearing chamber has. Slip over collar with set screws to hold it in place. There is an integral groove which maybe a o-ring should have...
    32 replies | 1688 view(s)
  • barrabruce's Avatar
    07-11-2020, 04:48 AM
    I’m trying to sort out some of the possibilities to put this back together and get the spindle pre loaded and running true. I’m figuring a slow drying Loctite so one could assemble everything and hopefully tweak things into place. Or am I being...
    32 replies | 1688 view(s)
No More Results
About barrabruce

Basic Information

About barrabruce
Still alive and plodding
Far Nth Qld Australia
Classic Camp Stoves, Fishing and the odd angry shot


Total Posts
Total Posts
Posts Per Day
Total Albums
Total Photos
General Information
Last Activity
Today 06:24 AM
Join Date
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check