Graf & SonsRepackboxWidenersInline Fabrication
RotoMetals2StainLess Steel Media

  • barrabruce's Avatar
    01-09-2019, 08:39 PM
    I have found that a ugly looking homemade dipper gets more of the "this guy is completely wacko and is gunna blow him self up" response to a more "Ohh using a dipper like the old times did.....like it will sort of work but not accurate and you’d...
    17 replies | 330 view(s)
  • barrabruce's Avatar
    01-09-2019, 08:06 PM
    Itís a A G Parker sight. The little right hand foot on the A makes it look like a A instead of a P. Could be what Iím looking for. One that goes onto the Rimfire scope groove. Need more picks. The second upload didnít work.
    4 replies | 136 view(s)
  • barrabruce's Avatar
    01-05-2019, 02:57 PM
    So is your pick handle and ideal type seater just a plugged case with a handle? Or do the you place the bullet in the case mouth and the stem slides in the case to seat it once the case is in the chamber? Does it really matter? Thnx
    10 replies | 323 view(s)
  • barrabruce's Avatar
    01-04-2019, 05:30 PM
    Maybe a rack like 22lr cases are held in. Then place in tin and add melted lube to correct height. I’ve tried dipping my loaded 310 cases in melted lube. I ended up with more lube on the nose than in the lube groove if I had the bullet hot or a...
    28 replies | 851 view(s)
  • barrabruce's Avatar
    01-02-2019, 01:55 PM
    I’ll match ‘yer red dot and lower you to 2.5 gns bullseye.(25 yrd load). If you up it to 3.5-4.0 gns you get about cci quiet loads Up to about 6.4 gns your looking at the std or target velocity 22lr. These shoot for me accurately out to 328 yrds.
    18 replies | 916 view(s)
  • barrabruce's Avatar
    12-26-2018, 08:43 PM
    Mine likes 15.5 a2205 over a 150 or 170 grn pp bullet. Velocity around 1550fps. 4227 /4198 on the burn rate charts. Mild mannered accurate and clean burning. A ss shot 30-30 thou. I find slower powders leave mummies in my bore but can be...
    18 replies | 916 view(s)
  • barrabruce's Avatar
    12-21-2018, 06:39 AM
    I don’t think ball powders behave themselves in reduced loadings. Bullseye has been my go to powder for this work but have used others as well. I’d stick with your red dot. Scoop and tickle up if needed. I have a habit of having my cases...
    28 replies | 2585 view(s)
  • barrabruce's Avatar
    12-21-2018, 06:17 AM
    I ladle pour cos Iím to stingy to by a letric one and have to run leads here or there. I mostly positive pour as in put the spout into the mould ala Lyman style. I get a nice flat full base. If I pour from a ways above the mold I donít seem to...
    59 replies | 1969 view(s)
  • barrabruce's Avatar
    12-21-2018, 04:42 AM
    Havenít seen anything in years Expensive when bought from enviro-mart but what the hell.. Garrenteed no leading now that Iím equipped again. The only other thing Iíve seen are a copper scrubber in a pan for cleaning electronic solering tips....
    96 replies | 83627 view(s)
  • barrabruce's Avatar
    12-17-2018, 09:03 AM
    Ohh have you thought about breachseating bullets? Brass will last like for Eva with out any need for anything more than a new primer and maybe a wipe over. Or the pope type tapered bullet. Stop ring bullet? Cast ...lube shoot. Reprime Dump a...
    47 replies | 1960 view(s)
  • barrabruce's Avatar
    12-17-2018, 08:36 AM
    I have a 30-30 handi rifle with 1:12 barrell It will do all I really need without making my teeth rattle and does well with low velocity cast loads as well. I like my 310 cadet and it is a hoot to shoot for me. I would like to build a 30-30...
    47 replies | 1960 view(s)
  • barrabruce's Avatar
    12-17-2018, 07:49 AM
    Had some time when I went to town and I thought could get a 3/4’ nut 14 tpi 55^ and enquire about the clips. No nut but :shock: shock I bought 10 C or E clips. At the other place I found a bspp 1/2" pipe coupler to fit. A bit loose but good to...
    53 replies | 3998 view(s)
  • barrabruce's Avatar
    12-17-2018, 07:21 AM
    Modified a 30-30 lee loader I got cheap for parts today. I can size cases down now to seat a bullet. Be better if I could make the mould a thou or two bigger on the base band and the heal 4 thou bigger. They would be a snug fit in the fired...
    52 replies | 6784 view(s)
No More Results
About barrabruce

Basic Information

About barrabruce
Biography:
Still alive and plodding
Location:
Far Nth Qld Australia
Interests:
Classic Camp Stoves, Fishing and the odd angry shot

Statistics


Total Posts
Total Posts
1,290
Posts Per Day
0.36
Albums
Total Albums
2
Total Photos
17
General Information
Last Activity
Today 06:33 PM
Join Date
02-09-2009
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check