RotoMetals2MidSouth Shooters SupplyTitan ReloadingGraf & Sons
ADvertise hereInline FabricationLee PrecisionStainLess Steel Media

  • starmac's Avatar
    Today, 06:28 PM
    All the technology in the world, the flattest shooting round in the world, understanding wind drift and all the practice in the world, all adds up. The quarry has not changed so does not know he isn't suppose to turn, take a step, whatever between...
    100 replies | 3042 view(s)
  • starmac's Avatar
    Today, 05:50 PM
    I agree with everything you have said, my response was geared to those that say to use a 350 gr or so for deer and move step it up for moose. Moose are thin skinned, and ordinarily do not have the tenacity to live as an elk, or even a deer. Eve a...
    32 replies | 1809 view(s)
  • starmac's Avatar
    Today, 02:41 AM
    I am kind of a one load kind of guy myself, but I have to ask, those that claim to stick with the heavies for moose, would you not hesitate to shoot one with a 30/06, 308, 358 etc??
    32 replies | 1809 view(s)
  • starmac's Avatar
    Today, 01:16 AM
    Most good western wear stores cleaned and blocked hats, they used steam, not sure how a wool hat would do with that. Who knows where a good western store anymore, they are getting scarce as hens teeth.
    7 replies | 256 view(s)
  • starmac's Avatar
    Yesterday, 07:05 PM
    starmac replied to a thread Ford mechanic question in Our Town
    Hopefully that does it, the only real way to see, is either wait and see if it does all right on longer trips, where to see if the pump heats up, or run it for an hour or so and then check fuel pressure with the vacuum line pulled off of the...
    35 replies | 807 view(s)
  • starmac's Avatar
    Yesterday, 05:46 PM
    I don't know if they still make the very same pants, but about 15 years ago I bought 2 pair of carhart insulated pants, with full length zippers on the legs. These are like the bibs, but just the pants and I wear them pretty much every day I work in...
    16 replies | 284 view(s)
  • starmac's Avatar
    Yesterday, 05:20 PM
    Yup, there is a valid reason the old phrase (old fool) was coined, and that was even before my time. lol
    18 replies | 837 view(s)
  • starmac's Avatar
    Yesterday, 02:56 PM
    I have found that is not always the case. lol That said, when Larry speaks, I listen.
    18 replies | 837 view(s)
  • starmac's Avatar
    Yesterday, 02:42 PM
    starmac replied to a thread Ford mechanic question in Our Town
    Hopefully that is the end of it, but that has not been my experience. 9 out of 10 times I have had a ford quit because the filter stopped up, it had already basically killed the pump trying to pump through a mostly stopped up filter, and it had to...
    35 replies | 807 view(s)
  • starmac's Avatar
    Yesterday, 03:27 AM
    You guys must have some sensational bears if you are worried about reloading while one is attacking?
    23 replies | 481 view(s)
  • starmac's Avatar
    Yesterday, 01:48 AM
    starmac replied to a thread Sams club closing. in Our Town
    They cited transportation cost as one of the reasons for closing the 3 in Alaska, no problem believing that, but then again the very same trucks deliver to the 4 wallmart stores, HMMM.
    50 replies | 1769 view(s)
  • TNsailorman's Avatar
    01-15-2018, 11:08 PM
    TNsailorman replied to a thread Sks in Military Rifles
    Back in the 80's, my brother bought a couple of the milled receiver Russian SKS's (one for himself and one for his teenage son). I shot the nephew's rifle one time at the range. My brother threw a tennis ball out to about 25 yards and I had no...
    21 replies | 595 view(s)
  • TNsailorman's Avatar
    01-15-2018, 10:59 PM
    I am not knowledgeable enough to answer your question on lot numbers. Maybe someone else can chime in and help. james
    6 replies | 189 view(s)
  • TNsailorman's Avatar
    01-15-2018, 04:29 PM
    What do the holsters fit?
    1 replies | 352 view(s)
  • TNsailorman's Avatar
    01-15-2018, 04:28 PM
    Outpost75, If I had know then what I know now, I would have gone the same route you did but I did not. Upshot was, I lost a beautiful .44-40 revolver because Ruger did not do the due diligence to make the revolver right in the first place and I did...
    26 replies | 853 view(s)
  • TNsailorman's Avatar
    01-15-2018, 03:18 PM
    sending pm on #4.
    6 replies | 766 view(s)
More Activity
About Arctic Blues

Basic Information


"The rifle is a weapon. Let there be no mistake about that. It is a tool of power, and thus dependent completely upon the moral stature of its user. It is equally useful in securing meat for the table, destroying group enemies on the battlefield, and resisting tyranny. In fact, it is the only means of resisting tyranny, since a citizenry armed with rifles simply cannot be tyrannized."

óJeff Cooper, The Art of the Rifle


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
02-13-2014 03:30 PM
Join Date

22 Friends

  1. 44man 44man is offline


  2. 45 2.1 45 2.1 is offline


    45 2.1
  3. 454PB 454PB is offline

    Boolit Master

  4. 45nut 45nut is offline

    Cast Boolits Founder/B.O.B.

  5. Bullshop Bullshop is offline


  6. Circuit Rider Circuit Rider is offline

    Boolit Master

    Circuit Rider
  7. Doby45 Doby45 is offline

    Boolit Master

  8. gee-gaw gee-gaw is offline

    Boolit Man

  9. jackley jackley is offline

    Boolit Master

  10. john hayslip john hayslip is offline

    Boolit Master

    john hayslip
Showing Friends 1 to 10 of 22
Page 1 of 3 123 LastLast
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check