MidSouth Shooters SupplyStainLess Steel MediaADvertise hereRotoMetals2
Graf & SonsTitan ReloadingLee PrecisionInline Fabrication

Tab Content
  • mazo kid's Avatar
    04-19-2018, 06:20 PM
    I came across 4 new file handles at a garage sale for very little money. But, I also make my own handles from scrap hardwood/ dowels. I like to turn down the front end so that a short piece of EMT or copper pipe is a force fit on it. This helps...
    45 replies | 1046 view(s)
  • mazo kid's Avatar
    04-19-2018, 09:46 AM
    Lefty here too. Early on, I owned and shot right hand cap and flint rifles. As stated before, eye (and ear) protection is a must. Also, watch your hand/arm position. The pan flash can give you a nice black powder "tattoo" on your right fore arm if...
    17 replies | 241 view(s)
  • mazo kid's Avatar
    04-16-2018, 12:04 PM
    I have a small jar of used clothes dryer sheets, use them to wipe down the powder measures. There are smokeless powders that will cling to the hopper tube also, Trail Boss being one of them. I sometimes use that in my cartridge conversion C&B...
    38 replies | 937 view(s)
  • mazo kid's Avatar
    04-16-2018, 11:39 AM
    Brass is spoken for by RKJ.
    3 replies | 111 view(s)
  • mazo kid's Avatar
    04-15-2018, 06:41 PM
    For the 38 Spl. brass I got from BuggyBuilder, I am offering 100 38 Super nickle brass. Mixed HS. Post here, followed by a PM to me with shipping info. Thanks.
    3 replies | 111 view(s)
  • mazo kid's Avatar
    04-13-2018, 10:48 AM
    mazo kid replied to a thread Winter projects in Muzzleloading.
    Ric, nice work as usual. Here in Wis. we are having some "alert" days this weekend. 6-12" snow mid-State, not quite as much for us. Coldest-ever start of April!
    33 replies | 884 view(s)
  • mazo kid's Avatar
    04-12-2018, 05:55 PM
    mazo kid replied to a thread 1866 Uberti in Leverguns
    I did check the chamber and found a slight patch of surface rust. Luckily no pitting! I spent a few minutes polishing it up with 0000 steel wrapped around a bore brush. I had checked the bore when I got the Carbine and it was clean and bright, so...
    12 replies | 314 view(s)
  • mazo kid's Avatar
    04-12-2018, 02:13 PM
    mazo kid replied to a thread 1866 Uberti in Leverguns
    Thanks for the comments and suggestions. Yes, the gun was used, and the ammo was "proved" in my Lyman multi-cartridge testing block. From reading I have done, it seems like the chambers were a little "loose" in those guns, so I was puzzled with the...
    12 replies | 314 view(s)
  • mazo kid's Avatar
    04-12-2018, 12:58 PM
    mazo kid started a thread 1866 Uberti in Leverguns
    I have wanted a lever gun in 38 or 38/357 for a long time. I got the Uberti Yellow Boy for a good price at an auction. When I went to function test it, the ammo chambered very hard! Ejected just fine. This was my reloaded ammo with commercial cast...
    12 replies | 314 view(s)
  • mazo kid's Avatar
    04-08-2018, 10:58 AM
    Thanks for those responses. After thinking about it, I realize I shouldn't have mentioned the Beaumont; I know better as I have several rounds loaded. The Mauser is different though in that IIRC , it uses a .445 boolit. The mold I referenced is a...
    4 replies | 274 view(s)
  • mazo kid's Avatar
    04-07-2018, 10:55 PM
    mazo kid replied to a thread 38 Special brass in Pay It Forward
    I could use that brass. Thanks. PM coming.
    1 replies | 155 view(s)
  • mazo kid's Avatar
    04-03-2018, 03:06 PM
    I have a chance to get a Lyman 445599 mold and was wondering what you may think about using those boolits in a Dutch Beaumont and/or an 84 Mauser?
    4 replies | 274 view(s)
  • mazo kid's Avatar
    04-03-2018, 10:36 AM
    PMs responded to.
    4 replies | 229 view(s)
  • mazo kid's Avatar
    04-02-2018, 02:12 PM
    I am looking for a Lee .457 HB mold, new or used in decent condition. Please state price or what you might trade for. Thanks.
    4 replies | 229 view(s)
  • mazo kid's Avatar
    03-25-2018, 12:49 PM
    +1 on drilling through holes, that would give very consistent length.
    33 replies | 1269 view(s)
No More Results
About mazo kid

Basic Information

Date of Birth
November 28
About mazo kid
Near Mazomanie, Wi.
Rendezvous, shooting m/l and BPCR
Retired electrician


NRA Life


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
04-20-2018 10:41 AM
Join Date

2 Friends

  1. fishhawk fishhawk is offline

    Boolit Master

  2. number7tn number7tn is offline

    Boolit Master

Showing Friends 1 to 2 of 2
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check