ADvertise hereTitan ReloadingRotoMetals2MidSouth Shooters Supply
Graf & SonsInline FabricationLee PrecisionStainLess Steel Media

Tab Content
  • BT Sniper's Avatar
    Yesterday, 12:23 PM
    Yep, I simply haven't attempted to make or use a pinch trim die yet. Will someday. Swage on! BT
    7 replies | 209 view(s)
  • BT Sniper's Avatar
    Yesterday, 10:28 AM
    Harbor freight. I drilled a hole in a round piece of aluminum the same diameter of the brass. I mounted this piece to a support, in my case I use a RCBS case trimmer base without any of the cutting tools or shell holders mounted to it. The hole...
    7 replies | 209 view(s)
  • BT Sniper's Avatar
    Yesterday, 12:44 AM
    I made a simple jig to use with mini chop saw. Trims them before deriming. BT
    7 replies | 209 view(s)
  • BT Sniper's Avatar
    03-19-2018, 12:53 PM
    I'll attempt to add my thoughts to the questions posted by the OP...... I can here some of you saying "oh no, but you provide these dies" so I'll try to keep it as un bias as possible. The target market? Well ........ quite simply anyone that...
    26 replies | 1546 view(s)
  • BT Sniper's Avatar
    03-12-2018, 12:03 AM
    BTSimple 22 cal mold has been modified to a three cavity mold. Three cavities seems to work better and is easier for me to machine and will still produce perfect results. Machining molds right now for current and future customers. Will be...
    121 replies | 18914 view(s)
  • BT Sniper's Avatar
    03-10-2018, 10:48 PM
    BT Sniper replied to a thread .40 S&W as jackets in Swaging
    I expand them after fully annealing them. Following thread has some good info on the process....
    19 replies | 662 view(s)
  • BT Sniper's Avatar
    03-10-2018, 10:46 PM
    Dillon media separator!
    5 replies | 280 view(s)
  • BT Sniper's Avatar
    03-10-2018, 10:43 PM
    Works very well. Check out some 25 cal bullets I made from 22 mag brass in the following thread.!&highlight=
    8 replies | 414 view(s)
  • sargenv's Avatar
    03-09-2018, 12:48 PM
    sargenv replied to a thread Herco ?? in Canister & Surplus Powder
    I use Herco exclusively for my 929 and 147 gr Polymer coated bullets. Anything else used with the 147's would cause sticky extraction or loss of accuracy. I settled on 3.7 gr in Starline 9mm brass. It is a nice mild ICORE and minor USPSA load.
    18 replies | 615 view(s)
  • sargenv's Avatar
    02-26-2018, 12:00 PM
    I used universal data for loading shotshells (20 gauge specifically) and tend to think that it was likely closer to international Clays as opposed to Universal as the 20 gauge ammo I made up with this stuff was a bit on the stout side..
    3 replies | 194 view(s)
No More Results
About sargenv

Basic Information

About sargenv
Bay Area, California
USPSA/ICORE shooting, Geocaching, Gardening, Cooking, Waterfowl hunting, and now making boolits
Tech Support


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Today 09:59 AM
Join Date

6 Friends

  1. ak47man ak47man is offline

    Boolit Mold

  2. BT Sniper BT Sniper is offline

    Vendor Sponsor

    BT Sniper
  3. runfiveswife runfiveswife is offline

    Boolit Lady

    • Send a message via Yahoo to runfiveswife
  4. spddrcr spddrcr is offline

    Boolit Mold

  5. Stick_man Stick_man is offline

    Boolit Master

  6. Superfly Superfly is offline

    Boolit Master

Showing Friends 1 to 6 of 6
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check