Graf & SonsRotoMetals2Inline FabricationMidSouth Shooters Supply
Lee PrecisionADvertise hereStainLess Steel MediaTitan Reloading

  • Beau Cassidy's Avatar
    07-08-2018, 10:35 PM
    I see I got my $25 stove for powder coating, my 40 lb Magma, and a bucket or 2 of ingots in the picture. A fella has to have his priorities!
    2283 replies | 1118460 view(s)
  • Beau Cassidy's Avatar
    07-08-2018, 10:20 PM
    Yesterday morning I coated those HP bullets and about 1,000 I made from an Arsenal .45 mold. I traded these bullets nd a few more for the lead ingots in another thread. Sent from my SM-G930V using Tapatalk
    881 replies | 121189 view(s)
  • Beau Cassidy's Avatar
    07-08-2018, 10:18 PM
    A few weeks ago I fired up a new waage pot and ladle case these NOE. 45 HP bullets. The individual bullets are scraped up because they hit the ground. They went into the reject pile Sent from my SM-G930V using Tapatalk
    881 replies | 121189 view(s)
  • Beau Cassidy's Avatar
    07-08-2018, 10:13 PM
    I had 6 of these ingots given to me today... well they cost me a few .45 bullets... more of these ingots are on the way. Supposedly are the counterweight on the breaker in the powerhouse below a hydroelectric dam. That must be one huge breaker! ...
    9 replies | 483 view(s)
  • Beau Cassidy's Avatar
    07-08-2018, 10:02 PM
    And about the big max presses... the one with the bent handle is my pride and joy. It belonged to Fred Huntington of RCBS. I haven't mounted the other 2 I have (and no- they aren't for sale) i had a 550 on the left side of the bench but, well, my...
    2283 replies | 1118460 view(s)
  • Beau Cassidy's Avatar
    07-08-2018, 09:49 PM
    The top weighed 150 lbs. As best I could weigh the base it was also 150 lbs. I didn't weigh the shelves but estimate about 75- maybe 80 lbs When I finished I thought the bare pine base looked plain so I took some thin cedar I had and basically...
    2283 replies | 1118460 view(s)
  • Beau Cassidy's Avatar
    07-08-2018, 09:42 PM
    Now for the bench... I have been planning it for years. I took 25 pine 2 by 4s and milled them all flat. I drilled 5 spaced holes thru each 2 by 4. They were all glued and clamped together in 2 halves. I then ran those 15 inch halves and ran them...
    2283 replies | 1118460 view(s)
  • Beau Cassidy's Avatar
    07-08-2018, 09:36 PM
    Finished unboxing everything today. It looks pretty good, I think. All of my dies, molds, and die parts are in a 40 inch rolling toolbox Sent from my SM-G930V using Tapatalk
    2283 replies | 1118460 view(s)
  • Beau Cassidy's Avatar
    07-08-2018, 09:34 PM
    3 coats of rubbed on Watco poly over 3 days standing with 220 in between coats. My 5 year old thinks it is a rack for her shoes. Sent from my SM-G930V using Tapatalk
    2283 replies | 1118460 view(s)
  • Beau Cassidy's Avatar
    07-08-2018, 09:32 PM
    First coat of finish. Danish oil rubbed in. Boy oh boy did it bring out the color! Sent from my SM-G930V using Tapatalk
    2283 replies | 1118460 view(s)
  • Beau Cassidy's Avatar
    07-08-2018, 09:31 PM
    Dont laugh at the joints. I have done very few of these dado cuts. For this bench they will have to suffice. Sent from my SM-G930V using Tapatalk
    2283 replies | 1118460 view(s)
  • Beau Cassidy's Avatar
    07-08-2018, 09:29 PM
    This is basically everything fit together. It's amazing how it fit differently laying down compared to sitting up. I put a walnut strip along the back wall (birch plywood) for strength using nails. Sent from my SM-G930V using Tapatalk
    2283 replies | 1118460 view(s)
  • Beau Cassidy's Avatar
    07-08-2018, 09:26 PM
    I was very nervous making the dado cuts One was actually off just as little. My 5 year old was my constant companion and here is checking the width of a piece of walnut. There was a lot of assembly/disassembly which was a headache because I was...
    2283 replies | 1118460 view(s)
  • Beau Cassidy's Avatar
    07-08-2018, 09:23 PM
    2 1/2 years ago a logger friend gave me some walnut, cherry, and poplar logs. I had them cut and let them dry for a few years. My goal was a walnut carcass with cherry shelves. Recently I started making the shelves/hutch for my bench. I had to mill...
    2283 replies | 1118460 view(s)
  • Beau Cassidy's Avatar
    06-29-2018, 07:59 PM
    I haven't fired up the 10-cavity H&G .38 SWC in a while but may be willing to help a fella in my area. I have a request in for the MiHec slick sided version of the RCBS which will make most everything else I cast with nearly obsolete. It is a...
    14 replies | 841 view(s)
No More Results
About Beau Cassidy

Basic Information

About Beau Cassidy
Location:
Nashvegas, TN

Signature


At one with the gun.

Statistics


Total Posts
Total Posts
1,337
Posts Per Day
0.27
General Information
Last Activity
Today 05:08 PM
Current Activity
Viewing Attachment
Join Date
03-20-2005
Referrals
0

1 Friend

  1. Sniper Doc Sniper Doc is offline

    Boolit Mold

    Sniper Doc
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check