ADvertise hereRotoMetals2Inline FabricationMidSouth Shooters Supply
Lee PrecisionWidenersTitan ReloadingRepackbox

Tab Content
  • wv109323's Avatar
    03-27-2020, 10:09 PM
    God created nothing evil. At the end of the days of creation God sums it up as "good". Evil or sin is when man behaves against God or his plan. Since the fall of Adam ,we are born with a sinful nature and must learn obedience(behavior) to God's...
    30 replies | 3115 view(s)
  • wv109323's Avatar
    03-27-2020, 09:40 PM
    The Bible claims that God created the heavens and earth. If the aliens are from the heavens then God created them too.
    62 replies | 5867 view(s)
  • wv109323's Avatar
    03-20-2020, 11:45 PM
    I cast for .45 acp , .38 Spec. and 9mm. The things that improved my casting the most are a PID and a hot plate. Things that help are pouring directly into the sprue plate hole (get the lead into the mold quickly). Keep the pot over 1/2 full....
    31 replies | 1009 view(s)
  • wv109323's Avatar
    03-19-2020, 02:55 PM
    I read no where that Lucifers power was reduced or taken away from him after his fall from heaven. Lucifer had/has great power especially in light and music. Many of the objects involving lighted space craft ,I believe are from the devil. After...
    62 replies | 5867 view(s)
  • wv109323's Avatar
    03-14-2020, 07:39 PM
    With one of my grandsons,who wanted to "play" with my guns, I showed him how to check if the gun is empty. I used a bolt action rifle,semi-auto rifle and pistols and revolvers. I would use an empty cartridge to show him the difference between...
    67 replies | 3784 view(s)
  • wv109323's Avatar
    03-13-2020, 08:39 PM
    A hand full of years ago, Walmart had a catalog that you could order guns from. Prices were competitive as I remember. I never did order a gun so I don't know how it worked.
    10 replies | 1507 view(s)
  • wv109323's Avatar
    03-12-2020, 12:20 AM
    I remember gas @27 cents a gallon before 1973. Worked at Krogers for $1.85 an hour. Milk was $1.21 a gallon. Bought a Dillon 450 in 1980 for $169.IIRC .38 JHP 125 G. bullets were $3.95 a hundred. 55 g. 224 were $3.00 a hundred A used 70 series...
    15 replies | 677 view(s)
  • wv109323's Avatar
    03-09-2020, 10:24 PM
    wv109323 replied to a thread PID Unit in Casting Equipment
    The basics are $40.00 if you can wire it yourself. Top of the line components are $80.00. After I rebuilt the thermostat and wiring/terminals on my pot 3 or 4 times, the PID was an obvious answer to get rid of all that. The problems always showed...
    27 replies | 1265 view(s)
  • wv109323's Avatar
    03-08-2020, 11:30 PM
    wv109323 replied to a thread Need PID Help in Casting Equipment
    It looks like the ssr was the problem. It is shorted across.
    3 replies | 271 view(s)
  • wv109323's Avatar
    03-08-2020, 10:15 PM
    wv109323 replied to a thread Need PID Help in Casting Equipment
    You may be right. If there is high load on the SSR (in my case the short of the element ) will the SSR fail in the "closed " mode? I reckon at simple continuity test across the ssr would tell me. I will test that.
    3 replies | 271 view(s)
  • wv109323's Avatar
    03-08-2020, 06:07 PM
    I have used my PID setup for several years.(Auburn SYL 2352) I turned it on today and I heard a "pop" Somehow the element shifted in the pot and had the element grounded. I have a fuse in the PID but it did not blow. It knocked the 120V breaker in...
    3 replies | 271 view(s)
  • wv109323's Avatar
    03-04-2020, 11:49 PM
    wv109323 replied to a thread New to the forum in Our Town
    Wecome, this is one of the better forums I have found.
    10 replies | 318 view(s)
  • wv109323's Avatar
    03-03-2020, 10:15 PM
    wv109323 replied to a thread Remington 582 in Rimfire Area
    They were know for their accuracy and design of the action. Many were converted to benchrest rifles. This entailed a heavy barrel and stock. The single shot was more desirable for the conversion.
    5 replies | 419 view(s)
  • wv109323's Avatar
    03-03-2020, 10:06 PM
    wv109323 replied to a thread c&r license? in Factory Rifles
    I have seen people sell similar rifles using C&R license. The law is grey when a firearm crosses the line.
    2 replies | 306 view(s)
  • wv109323's Avatar
    03-02-2020, 04:24 PM
    I would like opinions on the Otis cleaning system. I like the idea because it is compact and you can clean lever action and semi-auto rifles through the breech. What are your opinions?
    15 replies | 744 view(s)
  • wv109323's Avatar
    02-29-2020, 07:36 PM
    I live out in the sticks so far that I have to walk toward town to go hunting.
    41 replies | 2360 view(s)
  • wv109323's Avatar
    02-29-2020, 07:28 PM
    TTT Bump for the weekend
    5 replies | 842 view(s)
  • wv109323's Avatar
    02-28-2020, 07:40 PM
    Unknown primer arm and Lyman drop tubes are sold
    5 replies | 842 view(s)
No More Results
About wv109323

Basic Information

About wv109323
Biography:
Age 60
Location:
Lenore, WV
Interests:
Cars Guns Photography
Occupation:
Disabled

Statistics


Total Posts
Total Posts
2,324
Posts Per Day
0.57
General Information
Last Activity
03-27-2020 11:49 PM
Join Date
01-02-2009
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check