Titan ReloadingADvertise hereLee PrecisionInline Fabrication
RotoMetals2Graf & SonsStainLess Steel MediaMidSouth Shooters Supply

Tab Content
  • wv109323's Avatar
    12-09-2017, 09:14 PM
    wv109323 replied to a thread SAECO Mould #050 in Cast Boolits
    The H&G No.50 is a 148 gn. wadcutter with a small nose. It has 3 rounded grease grooves and 1 crimp groove. H&G was so dominant in molds their mold numbers were used by other manufacturers.
    10 replies | 182 view(s)
  • wv109323's Avatar
    12-03-2017, 04:26 PM
    A noticeable degradation of your steadiness (wobble area) will cause you to "snatch" or jerk the trigger. The end result is much worse than the initial lose in wobble area.
    21 replies | 588 view(s)
  • wv109323's Avatar
    12-01-2017, 07:34 PM
    wv109323 replied to a thread What lever guns to get? in Leverguns
    I think a Marlin 44 mag. and a Marlin 45-70.
    41 replies | 1093 view(s)
  • wv109323's Avatar
    12-01-2017, 07:22 PM
    Have you thought about having yours repaired? There are businesses that specialize in repairing instrument panels for vintage and current cars.
    10 replies | 419 view(s)
  • wv109323's Avatar
    12-01-2017, 12:59 AM
    Bach in the early 1980's my friend shot hunters pistol silhouette with a scoped model 14. The rams are 100 yards. He was the state champion several times. His load was 5.0 gn. of Unique with a 158 gn. cast bullet.
    108 replies | 2926 view(s)
  • wv109323's Avatar
    11-30-2017, 07:40 PM
    I have a Marlin in 44 mag. It needs a fat bullet due to bore size. The nominal size for a 44 mag rifle is .431 versus the bore of .429 for a pistol. I have settled on powder coating a bullet for this rifle. A powder coated cast bullet is about...
    21 replies | 456 view(s)
  • wv109323's Avatar
    11-26-2017, 05:05 PM
    I did the same thing except I laid the drill on it's side. I used a Makita drill and chucked the bolt (minus the bolt head)into the drill chuck. Why nickel brass? Would not plain brass be easier to trim?
    15 replies | 595 view(s)
  • wv109323's Avatar
    11-23-2017, 03:55 PM
    It depends on which two calibers you are talking about or how much work you want to do before switchouts. Most 22 conversions will fit any frame so you can have the original caliber plus a .22 LR without much trouble. The differences between 9MM...
    30 replies | 786 view(s)
  • wv109323's Avatar
    11-17-2017, 07:28 PM
    What is the proper procedure to install these? Or how do they work? Is the "nut" opposite the adjustment suppose to turn ? The sight is actually a Dan Wesson but they appear the same. The sight blade will not move to the right far enough shoot...
    3 replies | 224 view(s)
  • wv109323's Avatar
    11-12-2017, 02:07 PM
    I have that information on the 1911forum.com .
    4 replies | 297 view(s)
  • wv109323's Avatar
    11-12-2017, 02:01 PM
    wv109323 replied to a thread 38 Squib loads? in Cast Boolits
    The velocity should be much higher for the 148's. Is there a noticeably different amount of recoil between the two loads? A quicker powder may be a better application but 2400 should do OK. I would suspect the chrono results are incorrect.
    13 replies | 520 view(s)
No More Results
About wv109323

Basic Information

About wv109323
Biography:
Age 60
Location:
Lenore, WV
Interests:
Cars Guns Photography
Occupation:
Disabled

Statistics


Total Posts
Total Posts
1,888
Posts Per Day
0.58
General Information
Last Activity
Today 03:08 AM
Join Date
01-02-2009
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check