Titan ReloadingWidenersRotoMetals2Inline Fabrication
MidSouth Shooters SupplyLee PrecisionADvertise hereRepackbox

Tab Content
  • Pressman's Avatar
    Yesterday, 01:49 PM
    Minerat, that is where I was going, In think this project is going to fill a terabyte disk easily. It's also going to create a need for secure file back-up that I need to think about.
    27 replies | 702 view(s)
  • Pressman's Avatar
    Yesterday, 01:47 PM
    Very good question and the answer is a bit expensive. There are scanners that have software to flatten the image, these are made especially for books, they work mostly OK. Or you have to fabricate a "V" device to place the book in, hold the...
    27 replies | 702 view(s)
  • Pressman's Avatar
    Yesterday, 12:33 PM
    After some thought I decided against having a shop scan them. Many, many of the pages were stapled together before punching for the binder. Thus, there is a lot of hand work. I called Canon late yesterday and ordered the model referenced in the...
    27 replies | 702 view(s)
  • Pressman's Avatar
    03-27-2020, 06:57 PM
    There are 5 different models, for those who weren't born yet and then old guy, Preacher Jim:grin:
    9 replies | 156 view(s)
  • Pressman's Avatar
    03-27-2020, 05:42 PM
    Good advise, I think I'll check with my favorite print shop before I hit send with an order to Canon.
    27 replies | 702 view(s)
  • Pressman's Avatar
    03-27-2020, 10:50 AM
    Dapaki you are on to it. I have an idea to scan each binder into a single big PDF. I can make it available on line or offline easily. My major concern is scanner life cycle. I don't want to burn up three or four units getting through this,...
    27 replies | 702 view(s)
  • Pressman's Avatar
    03-26-2020, 10:40 AM
    I have one like that, It has a nut brazed to the frame allowing a slightly larger set screw to be used. It is not factory pretty, but it works well. I got it years ago from a cranky older gentleman who could be very short on patience with his...
    4 replies | 225 view(s)
  • Pressman's Avatar
    03-26-2020, 10:33 AM
    I need ideas and now is the time to work on this project. How to copy, catalog and store information. Looking at the attached picture shows the scope of the problem. 4 shelves, 6 feet long, 24 feet total of e-mail correspondence that needs to...
    27 replies | 702 view(s)
  • LUBEDUDE's Avatar
    03-25-2020, 09:04 PM
    I bought my first 550 in ‘86 and immediately kicked myself for not getting one sooner. Then as I became very active in IPSC and later CAS I was going through tons of pistol Ammo. I bought my first 1050 in ‘05 and beat myself up for not getting one...
    19 replies | 344 view(s)
  • Pressman's Avatar
    03-25-2020, 04:08 PM
    This case split on the opposite side, away from the firing pin indentation. That was my first thought. I have a pair of yellow Bausch & Lomb yellow lens shooting glasses that I had the lens replaced to limit the focus distance to the front...
    28 replies | 888 view(s)
  • Pressman's Avatar
    03-25-2020, 03:24 PM
    I have a 25 ft range in my basement where I normally shoot sub sonic and quiet cartridges. Sorting through the 22 collection this morning I found a partial box of these 60 gr Aguila's that I bought 20 years ago. Since I was shooting the 22...
    28 replies | 888 view(s)
  • LUBEDUDE's Avatar
    03-25-2020, 02:27 PM
    LUBEDUDE replied to a thread I have a fox again in Our Town
    With snakes you get a mixture of things since they only have one exit hole (cloaca) for elimination. Sometimes they pass Urates, sometimes poo, sometimes bile, sometimes urine, sometimes musk, and then they can pass any combination. Because...
    22 replies | 875 view(s)
  • Pressman's Avatar
    03-24-2020, 09:07 AM
    Pressman replied to a thread Could use a die in Helping Hands
    I have an orphan named Lee. It's marked 44/44M DO. I am not familiar with Lee dies though this looks like a sizer, there's a ring in the mouth of the die. Maybe some Lee users can educate me?? It's free to a new home.
    2 replies | 119 view(s)
  • Pressman's Avatar
    03-23-2020, 05:10 PM
    A proper castboolit shooter will have a lube/sizer for every caliber he shoots along with an adequate number of appropriately dimensioned sizing dies should he have more than one firearm in that caliber.
    25 replies | 627 view(s)
  • Pressman's Avatar
    03-22-2020, 11:58 AM
    The fine threads get clogged with dirt easily. A good oil and a bore brush spun inside the hole should clean the threads. If there is rust then re-tapping may be the only choice if you cannot get a die to thread in. The thread is an odd one,...
    42 replies | 19502 view(s)
  • Pressman's Avatar
    03-21-2020, 09:26 PM
    Thanks for clearing that up, I had always wondered.
    42 replies | 19502 view(s)
More Activity
About LUBEDUDE

Basic Information

About LUBEDUDE
Biography:
Old balding fat guy, like half the rest of the bunch here.
Location:
East Texas
Interests:
Shooting sports, reloading, casting, skiing, outdoors, etc.
Occupation:
F O

Signature


TEAM HOLLYWOOD

NRA- LIFE TSRA-LIFE SASS-LIFE

Statistics


Total Posts
Total Posts
2,613
Posts Per Day
0.64
General Information
Last Activity
Today 12:00 AM
Join Date
12-31-2008
Referrals
0

7 Friends

  1. Grasslander Grasslander is offline

    Boolit Man

    Grasslander
  2. gunfan gunfan is offline

    Boolit Master

    gunfan
  3. HGS HGS is offline

    Boolit Buddy

    HGS
  4. Jim Kitchen Jim Kitchen is offline

    Boolit Bub

    Jim Kitchen
  5. Pressman Pressman is offline

    Moderator

    Pressman
  6. seagiant seagiant is offline

    Boolit Master

    seagiant
  7. Tracvision Tracvision is offline

    Boolit Buddy

    Tracvision
Showing Friends 1 to 7 of 7
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check