Lee PrecisionRepackboxRotoMetals2Titan Reloading
Inline FabricationADvertise hereWidenersMidSouth Shooters Supply

Tab Content
  • Pressman's Avatar
    Today, 03:47 PM
    Pressman replied to a thread Need a Translation in Our Town
    7.62 \t, \ І BULLETS WITH JNIVERSALJ-ZRІ! OM M2 22 PCs. GUNPOWDER NCD-02 MBJJ 57011 I copied it into Word, Microsoft says it is Serbian.
    3 replies | 195 view(s)
  • Pressman's Avatar
    Today, 10:49 AM
    Mr. Frog Person, the Bair will be in the archive. I need to look at the pre-war catalogs then I will have a package to get off to you. I have not found a catalog listing for Unique, though I have one so marked and another that I cannot determine...
    27 replies | 662 view(s)
  • Pressman's Avatar
    Today, 10:34 AM
    I’m kinda sad no one mentioned the Claymore.... Probably because he has it facing the wrong way, they were panicked and running for cover :roll:
    60 replies | 1977 view(s)
  • Pressman's Avatar
    Yesterday, 08:00 AM
    rmcc, what is in that big drawer of yours, do you have a SUMMER SPECIAL 2?? It was my favorite till I stopped carrying when I got married years ago.
    15 replies | 364 view(s)
  • Pressman's Avatar
    04-07-2020, 10:43 PM
    Mr. Frog Person sir, I have about a dozen rotor's, I will get a list to you. One is marked Unique. I am retaking pictures of the 5 variations, these will go to you. Next is digging through the catalogs to get approximate dates of production, I...
    27 replies | 662 view(s)
  • Pressman's Avatar
    04-07-2020, 10:05 PM
    On this board, in Swap & Sell. Or that evil bay.
    3 replies | 132 view(s)
  • Pressman's Avatar
    04-07-2020, 03:01 PM
    Nothing has changed other than the weather. It's getting warmer but no signs of spring just yet. Maybe a week or two. Inventory of tools, tinker with guns, research info for someone else to write an article, start scanning multiple thousands of...
    141 replies | 4807 view(s)
  • Pressman's Avatar
    04-06-2020, 07:20 PM
    fn1889m, on second thought. I took a look at my press this afternoon. I bought it new in 1999 as a gift for a friend who has since passed away and the press is mine again. The link arms and pivot block are looser than a goose. But, the problem...
    5 replies | 155 view(s)
  • Pressman's Avatar
    04-06-2020, 12:44 PM
    Pressman replied to a thread PIF swap box in Pay It Forward
    The box is in the mail, should see it Monday if not sooner. I Took: Lee Loader 7mm Rem Mag- only thing missing is the decap rod Vintage outers 22 rifle cleaning rod Leupold base/rings( d&t req.) for Ruger Blackhawk I added: 9 small bags...
    154 replies | 23512 view(s)
  • Pressman's Avatar
    04-06-2020, 10:17 AM
    Get enough wave washers to take up the slack in the pivot block/ frame fit. Then decide how you like it. A little play in the ram doesn't always hurt anything, but it can be disturbing to our sense of how things work. Getting a brass shim in the...
    5 replies | 155 view(s)
  • Pressman's Avatar
    04-04-2020, 11:26 PM
    Pressman replied to a thread PIF swap box in Pay It Forward
    The box will be sent Monday, stuffed with goodies
    154 replies | 23512 view(s)
  • Pressman's Avatar
    04-04-2020, 06:48 PM
    Pressman replied to a thread PIF swap box in Pay It Forward
    The Post Office did good, the box arrived today and in fine condition. I have pulled a couple of items out and will be busy looking for goodies his weekend to refill it, probably in a larger box. I plan to have it ready to mail Monday. Too...
    154 replies | 23512 view(s)
  • Pressman's Avatar
    04-03-2020, 02:47 PM
    My 1917 Carl Gustav. 18 years ago I had owned my first Swede. I fell in love with the 6.5 cartridge and that rifle. I like their lines, how they balance in the hand, the beautiful workmanship and just holding them. And they are fun to shoot. Then...
    76 replies | 9035 view(s)
  • Pressman's Avatar
    04-01-2020, 10:38 PM
    When I built my bench way back in 1995 I set it up with bread boards that slide into a series of slots in the front edge of the bench, a very similar system to what blind shooter uses. I have enough presses that I can have a separate press...
    46 replies | 1694 view(s)
  • Pressman's Avatar
    04-01-2020, 07:43 PM
    I agree. I have had the same problem as #2, only with 222 cases. Unscrewing the die would allow the extractor to get a grip and eventually pull the case out, it worked though it was a slow process. I have a set of 310 handles that are made for...
    7 replies | 1163 view(s)
  • Pressman's Avatar
    03-30-2020, 05:22 PM
    Is there a screw on the left side to lock the sprue plate pivot screw? I cannot quite tell from the picture. If not, then it is an original Ideal, 1st gen mould made prior to 1902.
    16 replies | 430 view(s)
More Activity

Basic Information

Old balding fat guy, like half the rest of the bunch here.
East Texas
Shooting sports, reloading, casting, skiing, outdoors, etc.





Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Today 05:58 PM
Join Date

7 Friends

  1. Grasslander Grasslander is offline

    Boolit Man

  2. gunfan gunfan is offline

    Boolit Master

  3. HGS HGS is offline

    Boolit Buddy

  4. Jim Kitchen Jim Kitchen is offline

    Boolit Bub

    Jim Kitchen
  5. Pressman Pressman is online now


  6. seagiant seagiant is offline

    Boolit Master

  7. Tracvision Tracvision is offline

    Boolit Buddy

Showing Friends 1 to 7 of 7
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check