Titan ReloadingInline FabricationRotoMetals2Wideners
MidSouth Shooters SupplyLee PrecisionRepackbox

Donate Now Goal amount for this year: 6000 USD, Received: 5505 USD (92%)
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


Tab Content
  • Gunlaker's Avatar
    08-10-2019, 05:20 PM
    Gunlaker replied to a thread Who knows? in Black Powder Cartridge
    I don't have one of those Uberti rifles, but I have a lot of other BPCR type rifles. I believe that the original Trapdoor rifles had a 1:22 twist and they stabilized the original 500gr bullet, so I wouldn't be afraid of a heavier bullet than a...
    9 replies | 349 view(s)
  • Gunlaker's Avatar
    08-09-2019, 08:02 PM
    I have used both Goex Fg and Swiss Fg. The Goex Fg seems to have big differences between lots. I've had one lot give very good results, and the next was unimpressive. This thread shows a 12 shot group from my CPA with plain Goex Fg at 223...
    5 replies | 273 view(s)
  • Gunlaker's Avatar
    08-09-2019, 12:53 PM
    Do you have a copy of the Black Powder Cartridge News article on that rifle, written by Kenny Durham a few years ago? He seemed to get decent accuracy with BP and has listed his bullets/loads to 500m. Have you tried slower powder? i.e. Swiss...
    5 replies | 273 view(s)
  • Gunlaker's Avatar
    08-03-2019, 05:05 PM
    RFD, is this the same Jim that makes their molds I wonder. I also find LDPE a little tricky to measure accurately. The wads I cut with their ".45 cal rifle" cutter certainly are easier to get into the case than their pre-cut wads are. Chris.
    34 replies | 1225 view(s)
  • Gunlaker's Avatar
    08-03-2019, 01:11 PM
    RFD, you can use one of Cornell's .45 Colt wad cutters to get that diameter, or thereabouts. I have cutters that do 0.450", 0.454" or so, and 0.459" or so. My rifles ( with Dan Theodore's 0.474" chamber mouth diameter ) work best with the bigger...
    34 replies | 1225 view(s)
  • Gunlaker's Avatar
    07-29-2019, 08:59 AM
    I bought a couple of reams of paper from BACO a number of years ago. It was made by Esleeck which made the paper in both 25% and 100% cotton. Both work just fine. I wouldn't worry about it much. I use a lot of Seth Cole paper and it's 25% if I...
    10 replies | 437 view(s)
  • Gunlaker's Avatar
    07-27-2019, 10:36 AM
    I use bullets from 0.443" to 0.446" depending on bore diameter and paper thickness. Chris.
    43 replies | 1692 view(s)
  • Gunlaker's Avatar
    07-24-2019, 03:27 PM
    That is excellent Ian! Chris.
    43 replies | 1692 view(s)
No More Results
About Gunlaker

Basic Information

Statistics


Total Posts
Total Posts
1,659
Posts Per Day
0.43
General Information
Join Date
12-14-2008
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check