Inline FabricationStainLess Steel MediaGraf & SonsADvertise here
Lee PrecisionTitan ReloadingRotoMetals2MidSouth Shooters Supply

  • clodhopper's Avatar
    Yesterday, 09:39 AM
    Brass from a .380 could be used to make .401 bullets. since they start out real close to .375 diameter bringing them up almost .020 in diameter would be the first step. But 9mm @.394 diameter, is so much easier to get, just cant see my self doing...
    249 replies | 128805 view(s)
  • clodhopper's Avatar
    06-17-2018, 12:46 PM
    Seeing the impact of misses is great feed back. Good on you for taking the effort of making your range fun and useful.
    7 replies | 295 view(s)
  • clodhopper's Avatar
    06-17-2018, 12:42 PM
    You could size bullets down to what?, .219? after making them.224. But it is an extra step over just making them .219 I the first place. If making .224 bullets is also in your future, it seems like a pretty good plan to avoid buying two sets...
    7 replies | 163 view(s)
  • clodhopper's Avatar
    06-01-2018, 09:42 PM
    Well if I was doing it, I would take piece of 2X4 lumber and cut a hole in it with a hole saw as close as possible to the diameter of your cylinder. Then cut across the hole with the grain, a rip cut. This piece of wood will allow you to grip the...
    11 replies | 499 view(s)
  • clodhopper's Avatar
    05-31-2018, 11:54 PM
    You could purchase a .373 chucking reamer for about 25 bucks. If it was my pistol, I would chuck the reamer and work it down each hole of the cylinder by hand. The existing holes would be good guides, don't force it, and don't sweat a few...
    11 replies | 499 view(s)
  • clodhopper's Avatar
    05-22-2018, 10:36 PM
    clodhopper replied to a thread Core dimentions? in Swaging
    Brian respectfully asks that his secrets not be given out. One quarter by one is truthful. I will not give you three digits to the right of the decimal.
    24 replies | 966 view(s)
  • clodhopper's Avatar
    05-22-2018, 01:02 AM
    clodhopper replied to a thread Core dimentions? in Swaging
    I can tell you the eleven cavity makes a heap of cores. Brass makes nice molds, but it's heavy. Carpal tunnel syndrome sucks.
    24 replies | 966 view(s)
  • clodhopper's Avatar
    05-21-2018, 06:00 PM
    clodhopper replied to a thread Core dimentions? in Swaging
    They are a quarter by one, with a pointy end. I run them through a core swage die for final dimension.
    24 replies | 966 view(s)
  • clodhopper's Avatar
    05-20-2018, 10:07 PM
    I would not say six chickens and four pigs sucked big time, unless my class was AAA or Master. That's really pretty good without putting in the range time for 77 and 100 meters yet.
    8 replies | 623 view(s)
No More Results
About muzzlebuster

Basic Information

About muzzlebuster
Location:
SW Montana
Interests:
shootin cast boolits
Occupation:
cabinetmaker/student

Statistics


Total Posts
Total Posts
0
Posts Per Day
0
General Information
Last Activity
07-28-2009 01:55 AM
Join Date
11-13-2008
Referrals
0

1 Friend

  1. clodhopper clodhopper is offline

    Boolit Master

    clodhopper
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check