RepackboxInline FabricationMidSouth Shooters SupplyADvertise here
Titan ReloadingWidenersRotoMetals2Lee Precision

Donate Now Goal amount for this year: 6000 USD, Received: 6135 USD (102%)
OUR GOAL HAS BEEN MET!
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


Tab Content
  • Intel6's Avatar
    Today, 11:49 AM
    I shoot both PC and HiTek bullets in my 45-70. I run gas checks on mine, not sure if they are needed but i do it anyway. I tried a 300 gr. bullet from a NOE mould and didnt have great results. It seemed that my Marlin didnt like the weight???...
    11 replies | 387 view(s)
  • Intel6's Avatar
    09-04-2019, 11:19 AM
    I also have the NOE ELCO mould and it is also a great mould. I like it better in my autos due to the blunt tip profile but is also shoots great in my 929. If I coulld have gotten it in an 8 cavity mould then I would have been satisfied but 5 cavity...
    18 replies | 626 view(s)
  • Intel6's Avatar
    08-30-2019, 11:50 AM
    Matrix, So far so good. I do both PC and HI Tek and tried both for the bullets. I didn't find any difference in how they shot (ransom rest) in my 929 so I just Hi Tek coat them as it is easier for me. I loaded and shot them in both my 929 and some...
    18 replies | 626 view(s)
  • Intel6's Avatar
    08-25-2019, 12:17 PM
    I was looking for the same thing but specifically for my 929. I was looking for a heavy RN bullet and a mould with a high cavity count. The MP moulds are the only ones that have an 8 cavity. I picked up a 151 gr. smooth mould and man does it crank...
    18 replies | 626 view(s)
  • Intel6's Avatar
    08-25-2019, 11:40 AM
    Intel6 replied to a thread 45-70 Govt 2400 in Cast Boolits
    I am also using 2400 as my standard powder in my 45-70 loads for my Marlin 1895SBL. I shoot a 360 gr. bullet with 22 grs. of 2400 as my all around shooing load.
    15 replies | 798 view(s)
  • Intel6's Avatar
    08-18-2019, 12:30 AM
    Gus, I like it a lot. It is my primary shooting bullet in 10mm now. My revolver likes the 220 gr. sightly more but all my autos love this bullet and I still use it in my revolver. I was seating them to leave a bit of the shouder out like in the...
    21 replies | 772 view(s)
No More Results
About Intel6

Basic Information

Statistics


Total Posts
Total Posts
395
Posts Per Day
0.08
General Information
Last Activity
Today 12:05 PM
Join Date
07-10-2005
Referrals
0

1 Friend

  1. NTD NTD is offline

    Boolit Bub

    NTD
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check