RotoMetals2Lee PrecisionWisconsin TriggerGraf & Sons
MidSouth Shooters SupplyInline FabricationTitan ReloadingStainLess Steel Media

Tab Content
  • Intel6's Avatar
    Yesterday, 06:16 PM
    I have been experimenting with non-heeled bullets in my original chambered Cadet. I have a few different bullets I have that are sized to .313" that seem to work decent. In the pic below L to R: 32-20 case with thinned rim and RCBS 120...
    10 replies | 363 view(s)
  • Intel6's Avatar
    Yesterday, 05:57 PM
    Same here, easy to use and easy to get other sizes needed.
    10 replies | 447 view(s)
  • Intel6's Avatar
    07-16-2017, 12:03 PM
    Hmm...that's what those are? I have a handful of those rounds loaded. I knew they were different so I didn't mess with them but I didn't know they were used for that? Thanks for the info!
    20 replies | 1026 view(s)
  • Intel6's Avatar
    07-16-2017, 11:58 AM
    Intel6 replied to a thread Elco tc hp in Cast Boolits
    1.145" for the auto and 1.150" for the revolver. I have shot the auto load in a few different Glocks and a Keltec 9mm carbine that uses Glock mags. I haven't tried it in anything else. Neal in AZ
    122 replies | 13148 view(s)
  • Intel6's Avatar
    07-16-2017, 11:40 AM
    Intel6 replied to a thread Annealing shells in Swaging
    I put the cases in those 50 round plastic ammo trays base first and then flip them over on some cement pavers. That way the case head it facing up and I can ensure I get a good anneal on the thicker head when I hit them with a propane weed burner.
    14 replies | 322 view(s)
  • Intel6's Avatar
    07-09-2017, 11:24 AM
    Intel6 replied to a thread Elco tc hp in Cast Boolits
    Yes, see post #92 Neal in AZ
    122 replies | 13148 view(s)
  • Intel6's Avatar
    07-09-2017, 11:00 AM
    I have the NOE 37 gr., both plain base and GC 45 gr. WFN and the 55 gr. RCBS copy. Since I have magazine fed Anschutz hornets I tend to use the 37 gr. quite a bit as it seems to have the best shape for that. I do use the WFN in my single shot...
    2 replies | 290 view(s)
  • Intel6's Avatar
    07-02-2017, 01:23 PM
    I use soft lead and HiTek coat mine. 10 gr. of Unique pushes them out just under 1,000 fps in my Marlin 1895 SBL. They shoot right on at 50 yds with my scope setting for the heavier 45-70 loads.
    7 replies | 331 view(s)
  • Intel6's Avatar
    07-02-2017, 12:44 PM
    Intel6 replied to a thread Help with dented bullets in Swaging
    I get the same sort of "crease" in some of my bullets. I found it was right where there was a lube groove in my cast core. Doesn't always happen, just seems to be the right combination of core and case. Two ways to stop it are use a smooth sided...
    18 replies | 677 view(s)
  • Intel6's Avatar
    06-23-2017, 06:46 PM
    Here is a pic of the NOE Frankenstein bullet I load in my 8x56R cartridges. I coat them with Hi Tek and either use "the load" or 2400. I started with the 16 grs. of 2400 load and worked up for a bit more power.
    12 replies | 537 view(s)
  • Intel6's Avatar
    06-23-2017, 06:42 PM
    Intel6 replied to a thread N.O.E. Problems... in Cast Boolits
    I have found with some of my NOE moulds that it takes a few casting sessions to get them going good. Not sure why but I have had it happen more than once where on the third session a switch flips and they start turning out great. Now if I have one...
    55 replies | 2367 view(s)
No More Results
About Intel6

Basic Information

Statistics


Total Posts
Total Posts
326
Posts Per Day
0.07
General Information
Last Activity
Yesterday 06:20 PM
Join Date
07-10-2005
Referrals
0

1 Friend

  1. NTD NTD is offline

    Boolit Buddy

    NTD
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check