MidSouth Shooters SupplyInline FabricationRepackboxWideners
Graf & SonsTitan ReloadingStainLess Steel MediaLee Precision
Tab Content
  • MUSTANG's Avatar
    Yesterday, 07:08 PM
    MUSTANG replied to a thread Moving to Reno in Our Town
    1. Take the Nevada CCW Course. At the same time; if the course supports it, make sure that you also get the paperwork for a Utah CCW Permit (This is common for many of the Instructors in Nevada to run classes that meet both States Requirements)....
    7 replies | 139 view(s)
  • MUSTANG's Avatar
    Yesterday, 10:08 AM
    It is definitely a case of the Barrel being stressed over it's ability to contain the pressure. Note in picture one and three that the rupture is fairly straight down the barrel; with what almost looks like a "Seamed Edge" along each side of the...
    18 replies | 458 view(s)
  • MUSTANG's Avatar
    10-15-2018, 08:31 PM
    MUSTANG replied to a thread mountain lion in NH in Our Town
    Must of been the same company that did the Pocahontas (Sen. Elizabeth Warren) DNA Testing. We had a set Cougar prints out back of the house (Kalispell house) last week. Didn't get into the Chicken pen, Rabbit hutch,. or bother the horses so...
    41 replies | 1022 view(s)
  • MUSTANG's Avatar
    10-14-2018, 10:42 AM
    I just hope that they put the Savage 12FV on sale again for the Fall/Christmas cycle. Want to add an inexpensive Savage .308 to my inexpensive Remington 700 in .308. Lots of Remington 700's and Savages in the safe; but I like to take inexpensive...
    56 replies | 3108 view(s)
  • MUSTANG's Avatar
    10-13-2018, 10:23 PM
    Must be an Ancestor of "Block Chain",Bit Coin, etc... Guess I will never have any of these.
    9 replies | 961 view(s)
  • MUSTANG's Avatar
    10-12-2018, 11:42 AM
    MUSTANG replied to a thread Help retreving iPad in Our Town
    Measure how far down the Computer is. Cut a hole in the dry wall. Pull out computer, patch and paint dry wall.
    41 replies | 1460 view(s)
  • MUSTANG's Avatar
    10-11-2018, 10:08 PM
    MUSTANG replied to a thread Help retreving iPad in Our Town
    A good, strong suctions, vacuum cleaner with hose. Run the hose down the vent turn on the vacuum and try to get the circular opening of the hose to contact a flat surface on the computer. It will "Suck down Tight" on the flat surface, the vacuum...
    41 replies | 1460 view(s)
  • JKH's Avatar
    10-11-2018, 09:07 PM
    16 pounds WC846 for $215 shipped, time to load lots of 7.62Nato ��
    1875 replies | 310247 view(s)
  • MUSTANG's Avatar
    10-04-2018, 05:00 PM
    Sound advise. We looked at "Weekend" places in Utah a couple decades ago so we could get out of the LAsVegas Basin desert on weekends in the summer. Accessing water is very difficult. Most water rights have been assigned in Utah; this includes...
    32 replies | 1266 view(s)
  • Rio Grande's Avatar
    09-30-2018, 05:33 AM
    The steel one is part of a USGI adapter assembly... the one on the right in the first photo in the link... https://www.americanrifleman.org/articles/2016/4/3/cartridge-adapters/
    3 replies | 418 view(s)
  • MUSTANG's Avatar
    09-27-2018, 09:51 AM
    One could always go with applications on Flat Surfaces to reduce the noise level:
    31 replies | 866 view(s)
  • Rio Grande's Avatar
    09-25-2018, 08:13 PM
    I don't know. This vintage rifle was so fine and factory original I'd hesitate to modify it, butt plate and all.
    14 replies | 1137 view(s)
  • MUSTANG's Avatar
    09-25-2018, 07:48 PM
    I have three of these on top of the Wood Stove, one face straight forward, and the other two about 30 offset from the center fan: ...
    31 replies | 866 view(s)
  • Rio Grande's Avatar
    09-24-2018, 08:39 PM
    The bore is fine indeed. I see no problem with replacing the trigger guard and spacer, but I would hesitate to modify too much otherwise from original.
    14 replies | 1137 view(s)
  • Rio Grande's Avatar
    09-22-2018, 10:09 AM
    Thank you Outpost. I did not know that.
    14 replies | 1137 view(s)
  • Rio Grande's Avatar
    09-22-2018, 01:18 AM
    Thanks. Your PM responded to. I'll meet 1/2 way.
    14 replies | 1137 view(s)
  • Rio Grande's Avatar
    09-22-2018, 01:17 AM
    You are right, but I'm no great hand w/ posting pics. :)
    14 replies | 1137 view(s)
  • MUSTANG's Avatar
    09-21-2018, 09:37 AM
    MUSTANG replied to a thread Welcome aboard Wideners! in Our Town
    Went to their website. No powder, no primers, and limited Brass offerings. Mostly loaded ammunition and jacketed bullets. Wonder why they want to advertise on this site?
    20 replies | 841 view(s)
  • Rio Grande's Avatar
    09-21-2018, 05:42 AM
    SOLD to Nueces Priority to local Houston-area sale but will consider shipping. This is a good one. Model 158 Topper 'Z' code next to patent number, no serial number, which indicates 1963-made if I am correct. I estimate over 90% condition,...
    14 replies | 1137 view(s)
More Activity
About JKH

Basic Information

About JKH
just another firearm enthusiest whos getting older but not necessarily smarter ;^ )
guns, loading, books, remodeling, photography, clock repair, etc.
Construction Rehabilitation Specialist


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
10-11-2018 09:07 PM
Join Date

4 Friends

  1. MUSTANG MUSTANG is offline

    Boolit Master

  2. number7tn number7tn is offline

    Boolit Buddy

  3. onondaga onondaga is offline


  4. Rio Grande Rio Grande is offline

    Boolit Buddy

    Rio Grande
Showing Friends 1 to 4 of 4
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check