Inline FabricationRepackboxMidSouth Shooters SupplyLee Precision
RotoMetals2Titan ReloadingWidenersADvertise here

Donate Now Goal amount for this year: 6000 USD, Received: 4555 USD (76%)
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


Tab Content
  • No_1's Avatar
    Today, 05:31 AM
    Yup - software upgrade.
    16 replies | 715 view(s)
  • HATCH's Avatar
    Yesterday, 08:22 PM
    HATCH replied to a thread Help with PID in Casting Equipment
    If you measuring DC voltage then it would be safe to assume there is a issue with that PID. Sent from my iPhone using Tapatalk
    24 replies | 510 view(s)
  • HATCH's Avatar
    Yesterday, 05:28 PM
    HATCH replied to a thread Help with PID in Casting Equipment
    According to his model # it is a dc voltage output model for the SSR. Sent from my iPhone using Tapatalk
    24 replies | 510 view(s)
  • No_1's Avatar
    Yesterday, 12:40 PM
    No_1 replied to a thread Heck of a storm in Our Town
    I have a Yamaha 1800 watt gen I purchased when HUGO came through 30 years ago. I had considered purchasing a huge gen as I thought I needed to run the whole house but when I saw the fueling requirements decided I only needed enough to keep the...
    28 replies | 428 view(s)
  • HATCH's Avatar
    08-10-2020, 12:50 PM
    According to the picture looks like 70 Sent from my iPhone using Tapatalk
    3 replies | 124 view(s)
  • No_1's Avatar
    08-10-2020, 10:40 AM
    Thank you for the support!
    16 replies | 715 view(s)
  • HATCH's Avatar
    08-09-2020, 11:30 AM
    Bump. Have one ready to ship Will be ordering more pids/ssr tomorrow Sent from my iPhone using Tapatalk
    34 replies | 38144 view(s)
  • HATCH's Avatar
    08-09-2020, 11:30 AM
    Currently two weeks out Sent from my iPhone using Tapatalk
    26 replies | 9920 view(s)
  • HATCH's Avatar
    08-09-2020, 11:11 AM
    HATCH replied to a thread Help with PID in Casting Equipment
    I unsubscribed to this thread so if you need any additional help send me a PM Sent from my iPhone using Tapatalk
    24 replies | 510 view(s)
  • No_1's Avatar
    08-08-2020, 07:02 PM
    And thatís a shame. Yíall spread the word that our doors are open for all that are looking for a new home.
    16 replies | 715 view(s)
  • HATCH's Avatar
    08-07-2020, 09:20 PM
    HATCH replied to a thread Help with PID in Casting Equipment
    That inkbird will work. Please keep in mind that there is a very slight possibility that the PID May of been damaged by using the incorrect SSR but I am pretty sure itís gonna be ok. Sent from my iPhone using Tapatalk
    24 replies | 510 view(s)
  • HATCH's Avatar
    08-07-2020, 05:38 PM
    HATCH replied to a thread Help with PID in Casting Equipment
    Your getting bleed thru voltage but no current Get the correct ssr Sent from my iPhone using Tapatalk
    24 replies | 510 view(s)
  • HATCH's Avatar
    08-07-2020, 11:58 AM
    unless the item was sent priority mail or express mail all other forms of mailing are delayed. It took four days for a package to go from the main hub to my little post office. 14 miles of road travel and typically depending on arrival to the main...
    65 replies | 1580 view(s)
  • HATCH's Avatar
    08-07-2020, 09:27 AM
    HATCH replied to a thread Help with PID in Casting Equipment
    I think I got something Looking over closely at the SSR, I noticed something. That model SSR uses 90-280 VAC on the control side. I believe that model PID provided a @7 volt output for the SSR. That would explain why you aren't getting any...
    24 replies | 510 view(s)
  • HATCH's Avatar
    08-07-2020, 09:21 AM
    HATCH replied to a thread Help with PID in Casting Equipment
    looks like its wired up right. need to verify voltages. I ran into a issue a couple months ago which caused me to make a 90 min service call to visit a Master Caster Panel customer. The pot would never get up to temp. I checked my voltages and...
    24 replies | 510 view(s)
  • HATCH's Avatar
    08-06-2020, 05:30 PM
    HATCH replied to a thread Help with PID in Casting Equipment
    Can you take a picture of your setup? I found the manual -> https://www.instrumart.com/assets/Red-Lion-T48-P48-Manual.pdf You should have a SSR that you are using. For discussion we are gonna label the ssr as the picture below shows 1...
    24 replies | 510 view(s)
More Activity
About HATCH

Basic Information

About HATCH
Location:
Lexington, SC

Signature


Don't like being hammered by the Cast Boolits Staff, then don't be a nail.
The rules are simple to follow.

Statistics


Total Posts
Total Posts
5,694
Posts Per Day
1.31
General Information
Join Date
09-01-2008
Referrals
5

15 Friends

  1. ThePatriot1776 ThePatriot1776 is offline

    Boolit Mold

    ThePatriot1776
  2. Toby8888 Toby8888 is offline

    Boolit Mold

    Toby8888
  3. wymanwinn wymanwinn is offline

    Boolit Buddy

    wymanwinn
  4. Y-Nots3D Y-Nots3D is offline

    Banned

    Y-Nots3D
  5. zzr7ky zzr7ky is offline

    Boolit Mold

    zzr7ky
Showing Friends 11 to 15 of 15
Page 2 of 2 FirstFirst 12
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check