Inline FabricationMidSouth Shooters SupplyLee PrecisionRotoMetals2
WidenersStainLess Steel MediaGraf & SonsTitan Reloading

Tab Content
  • jimkim's Avatar
    09-16-2018, 02:24 PM
    This is a 444 Marlin case that was necked down using a 40 S&W/10mm sizing die. You should be able to do the same thing. If it doesn't want to fit, you can use a 30-06 or similar die to put a taper on the neck. Sent from my SM-S820L using Tapatalk
    8 replies | 1156 view(s)
  • jimkim's Avatar
    09-12-2018, 12:26 PM
    I took an old rice cooker apart the other day. I was surprised to see it had a five hundred watt element. I am not tossing this thing. Because of the way it's made, I'm thinking it would make a perfect heated platform, for warming a mould, or two,...
    0 replies | 105 view(s)
  • billyb's Avatar
    08-28-2018, 04:56 AM
    do not know about Lee, when I was loading the 357 sig I bought a Redding taper crimp die that worked! until I started using it I run into some bullet setback.
    8 replies | 366 view(s)
  • jimkim's Avatar
    08-27-2018, 01:22 AM
    I want the large version of this. The round one I have works fine, I just think the larger pointer style knob looks better. I know that's a waste of money. http://www.guitarpartsresource.com/guitarknobs_chickenhead.htm Sent from my VS880...
    9 replies | 420 view(s)
  • jimkim's Avatar
    08-26-2018, 02:12 PM
    I was surprised they used them on a pot this old. Mine is like the one in the picture. Where can I find a large chickenhead knob? Sent from my VS880 using Tapatalk
    9 replies | 420 view(s)
  • jimkim's Avatar
    08-26-2018, 12:30 AM
    I crimped them on freshly stripped wire. I also made sure they were tight. I may go back later and convert it to rings. I'm also temped to replace the power cable and jumpers with heavier guage wires. I also replaced the mica plate(it fell...
    9 replies | 420 view(s)
  • jimkim's Avatar
    08-25-2018, 02:37 PM
    I had to replace a spade connector on my Lyman furnace earlier this week. Wish I had sooner. It's like a brand new furnace. I have to figure out the new temp settings now. I was running 7-9, depending on the mould. Now, I'm getting frost at 6. It...
    9 replies | 420 view(s)
  • billyb's Avatar
    08-23-2018, 02:46 PM
    One more bump
    6 replies | 639 view(s)
No More Results
About billyb

Basic Information

Date of Birth
May 16, 1947 (71)
About billyb
Biography:
retired with 33 years on FRISCO&BNSF railroad
Location:
okmulgee county oklahoma
Interests:
guns &woodworking
Occupation:
retired

Statistics


Total Posts
Total Posts
423
Posts Per Day
0.11
General Information
Last Activity
09-06-2018 02:04 PM
Join Date
04-04-2008
Referrals
0

1 Friend

  1. jimkim jimkim is offline

    Boolit Master

    jimkim
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check