Inline FabricationTitan ReloadingADvertise hereLee Precision
RepackboxMidSouth Shooters SupplyRotoMetals2Wideners

Tab Content
  • TomAM's Avatar
    Yesterday, 11:50 PM
    TomAM replied to a thread Dhl in Molds...Maintenance and Design
    Over the course of several years U.S. Customs has seized three of my international mold shipments. Some of the inspectors think they are illegal, classified as "Munitions of War". The U.S. Munitions list specifically exempts handloading tools, and...
    2 replies | 145 view(s)
  • M-Tecs's Avatar
    Yesterday, 09:30 PM
    These folks might have an answer on what alloy you have.
    2 replies | 78 view(s)
  • Dan Cash's Avatar
    Yesterday, 09:15 PM
    Dan Cash replied to a thread Pat Marlins in Gas Checks
    Pat is always having problems.
    3 replies | 95 view(s)
  • Wayne Smith's Avatar
    Yesterday, 04:29 PM
    Craft Supplies, Rocklear Hardware or WoodCraft, all online/catalog operations with some local stores.
    37 replies | 2861 view(s)
  • MiHec's Avatar
    191 replies | 23450 view(s)
  • BT Sniper's Avatar
    Yesterday, 02:02 PM
    BT Sniper replied to a thread My Work Order List in BT Sniper
    No luck deer hunting. Preparing for elk season, will be out of office for a week. Thank you to the few of you on my list for your patience and support. Brian
    417 replies | 132854 view(s)
  • lar45's Avatar
    Yesterday, 01:37 PM
    Looking great Oldfeller. Have you shot any of the buckshot loads yet? I'm very interested in how they group.
    105 replies | 4306 view(s)
  • W.R.Buchanan's Avatar
    Yesterday, 01:30 PM
    3B: Does the mouth of the chamber have a sharp edge? It looks like it does. If so refer to the sticky on the Leverguns forum about Chamfering the Chamber Mouth to promote feeding. The reason why your gun won't feed soft boolits is because the...
    6 replies | 442 view(s)
  • W.R.Buchanan's Avatar
    Yesterday, 01:14 PM
    There is a Show on the Outdoor Channel called "Wild Boar Fever" which is sponsored by Aimpoint and illustrates the use of Red Dot Sights on Bolt Action Rifles for shooting running wild boar in Europe. The Principle of the show is a German Prince...
    57 replies | 1764 view(s)
  • W.R.Buchanan's Avatar
    Yesterday, 12:25 PM
    Tarhunt's barrels are made by Shaw and they will be excellent. I don't understand why Taylor doesn't just send his gun back to Savage? If it has a bad barrel or some other problem It would get fixed for free as opposed to paying someone to do...
    66 replies | 2767 view(s)
  • TheCaptain's Avatar
    Yesterday, 12:13 PM
    Hi to all, Bumping to keep thread alive. Hopefully soon I will be ready to "take orders" for range lead ingots. Am in the process of smelting range lead that I fetched last week; and I had to cancel another pickup of lead that would have...
    27 replies | 2774 view(s)
  • marlinman93's Avatar
    Yesterday, 10:46 AM
    I'm not using the new Marbles tang sights. Mine is a period original Marbles for an 1893 that has the true 1.125" spacing. No Marlin repeater ever used anything but a 1.125" spacing, so not sure why Marbles would make a sight for the 1893 and not...
    6 replies | 165 view(s)
  • Larry Gibson's Avatar
    Yesterday, 10:00 AM
    I load a lot of M193 equivalent 5.56 NATO on a Dillon 550B. Once fired military cases are sizes with a standard 223 Rem RCBS X-die (most often is a single stage press), the primer pocket swaged (Dillon primer pocket swage) and the case mouth...
    9 replies | 181 view(s)
  • Larry Gibson's Avatar
    Yesterday, 09:41 AM
    The Rhineland barrel shanks are threaded long enough to fit into the deeper threaded M93 - M96 actions. Your M98 SR action is not threaded as deep because of it's internal collar as mentioned. Thus the excess threading sticks out. A simple...
    11 replies | 208 view(s)
  • M-Tecs's Avatar
    10-16-2019, 07:28 PM
    Even more odd is the arc or radius appears to be flatter than the radius of the machining marks???
    18 replies | 375 view(s)
  • W.R.Buchanan's Avatar
    10-16-2019, 04:25 PM
    Well it looks to me that Target #4 is the right ammo. Accurate Full Bore? What is that? I'd still try some Lightfield Slugs in it to see if they work. What you are looking for is an easily obtainable "Baseline" ammo that works, that you can...
    27 replies | 1001 view(s)
More Activity
About M-Tecs

Basic Information

About M-Tecs
Master Tool & Die Maker
Master Tool & Die Maker


2nd Amendment of the U.S. Constitution. - "A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed."


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Yesterday 11:40 PM
Join Date

116 Friends

  1. is offline

    Boolit Buddy
  2. 44minimum 44minimum is offline

    Boolit Buddy

  3. 45 2.1 45 2.1 is offline


    45 2.1
  4. 45nut 45nut is offline

    Cast Boolits Founder/B.O.B.

  5. 45stomp 45stomp is offline

    Boolit Buddy

  6. 9.3X62AL 9.3X62AL is offline

    Boolit Grand Master

  7. Alphawolf45 Alphawolf45 is offline

    Boolit Mold

  8. andremajic andremajic is offline

    Boolit Buddy

  9. Artful Artful is offline

    Boolit Grand Master

  10. ASSASSIN ASSASSIN is offline

    Boolit Buddy

Showing Friends 1 to 10 of 116
Page 1 of 12 1234567891011 ... LastLast
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check