RotoMetals2ADvertise hereRepackboxLee Precision
MidSouth Shooters SupplyInline FabricationTitan Reloading

  • Cast_outlaw's Avatar
    10-13-2020, 08:33 AM
    Let it burn off won’t hurt nothing I’d try to avoid breathing the smoke though
    2 replies | 111 view(s)
  • Cast_outlaw's Avatar
    10-13-2020, 08:32 AM
    Worked on my hunting truck spent two hours in a ditch the other weekend so made a receiver mount for the front of it for a winch now to build the back one and get them welded
    9304 replies | 925776 view(s)
  • Cast_outlaw's Avatar
    10-12-2020, 11:25 AM
    I would slug your bore on the rifle befor getting a sizer and be sure you got the right one I got a 311 for my 303 and turns out I needed a 313 so definitely slug it cerosafe is not that expensive and works great
    7 replies | 177 view(s)
  • Cast_outlaw's Avatar
    10-12-2020, 11:10 AM
    Loaded 10 30/40 cases with my S.G.L. 65gr OObuck sized 311 over 5gr Vectan AS accurate fast and effective the push through ram creates a nice flat spot I put facing forward think I had these clocked at 1550fps but are almost touching at 50m
    9304 replies | 925776 view(s)
  • Cast_outlaw's Avatar
    10-07-2020, 08:55 AM
    My rides. 01 gmc rust bucket with a duromax, 14’ tin boat with a 20hp and 24’ welded aluminum With twin 90s me and my dad built Wife’s ride is in the box to a scooter
    572 replies | 372553 view(s)
  • Cast_outlaw's Avatar
    10-07-2020, 08:38 AM
    Prayers sent
    38 replies | 899 view(s)
  • Cast_outlaw's Avatar
    10-03-2020, 12:18 AM
    I’m only going to to answer 3. Get the ingot molds from lake house he has two different versions they work great and stack well And 6. I use a cut off end of a Broken shovel Handel, Works good, and free
    27 replies | 683 view(s)
  • Cast_outlaw's Avatar
    10-02-2020, 03:46 PM
    I haven’t used ba9 but I know vectan as is similar in burn to red dot and very accurate in my 303 with the lee tl314-90 swc
    15 replies | 561 view(s)
  • Cast_outlaw's Avatar
    10-01-2020, 08:26 AM
    Cast_outlaw replied to a thread Shipping to Canada? in Our Town
    I’ve got a few molds from here into Canada just shipped as hand tools it on average was $20 ore more In Shipping Haven’t had any problems yet
    8 replies | 285 view(s)
  • Cast_outlaw's Avatar
    09-27-2020, 09:44 AM
    I personally would not keep one at a hunting cabin, as it’s easy in both Canada, and the us to transport one. If I had to, a hidden compartment in the floor or wall etc would be your best bet. just make sure they are dripping with some kind of oil...
    36 replies | 1276 view(s)
  • Cast_outlaw's Avatar
    09-27-2020, 09:20 AM
    Cast_outlaw replied to a thread Truck Gun Racks? in Our Town
    They are league in Canada just so you know you don’t need to have you guns disabling device on when you are transporting them they just can’t be loaded because a few hunters shot themselves pulling their guns out of vehicles I have a cheep set of...
    21 replies | 750 view(s)
  • Cast_outlaw's Avatar
    09-26-2020, 01:26 PM
    Thank you all again for you prayers and condolences in this tuff time for our family. We will be laying here to rest today under a willow tree in the cemetery, it was her plot of choice. She was a wonderful mother I could not have asked for a better...
    22 replies | 647 view(s)
  • Cast_outlaw's Avatar
    09-26-2020, 01:18 PM
    Cast_outlaw replied to a thread Thanking the lord in Our Chapel
    Thank you for all your thoughts and prayers it is appreciated and my the lord bless you and yours with health long life and lots of ammo
    10 replies | 289 view(s)
  • Cast_outlaw's Avatar
    09-25-2020, 11:55 AM
    I give thanks today for the lord not taking my SO away three years ago when she suffered a major stroke. I found her laying on her back in the living room moments after it started The emergency responders were in the house in under ten minutes after...
    10 replies | 289 view(s)
No More Results
About Cast_outlaw

Basic Information

About Cast_outlaw
B.C. Canada
Trap shooting hunting and fishing


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Today 08:40 AM
Join Date
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check