Inline FabricationRotoMetals2Lee PrecisionRepackbox
WidenersTitan ReloadingGraf & SonsMidSouth Shooters Supply

  • weeple2000's Avatar
    03-19-2019, 02:02 AM
    weeple2000 replied to a thread Noe 310-165-fn-h3 in Cast Boolits
    Here is a pic of the mold in question. I have it in my possession. This is my first NOE mold. Is it new? I would rather not clean it if it has been used.
    5 replies | 161 view(s)
  • weeple2000's Avatar
    03-13-2019, 11:05 AM
    weeple2000 replied to a thread Noe 310-165-fn-h3 in Cast Boolits
    Sent you a pm.
    5 replies | 161 view(s)
  • weeple2000's Avatar
    03-13-2019, 01:41 AM
    weeple2000 replied to a thread Noe 310-165-fn-h3 in Cast Boolits
    What are some other options with a larger flat point or meplat that would work in either of those rifles? From the NOE/Accurate/M&P/Arsenal options?
    5 replies | 161 view(s)
  • weeple2000's Avatar
    03-12-2019, 11:36 PM
    I did something I told myself I wasn't going to do. It seems that casting and reloading are a bit of a rabbit hole. I have been doing pretty well not buying a ton of guns. I am wondering if I am going to wind up with a collection of molds...
    5 replies | 161 view(s)
  • weeple2000's Avatar
    03-09-2019, 02:25 AM
    I did try dipping some. I was impatient and didn't wait for them to dry. I am not sure if that was the cause, but the coats weren't completely even on all of the boolits. Some had a side that didn't coat very well.
    23 replies | 712 view(s)
  • weeple2000's Avatar
    03-07-2019, 01:57 AM
    I reread the thread and realized that the answer to the last post was earlier in the thread. That I should be good to go. I have some hydro dipped boolits drying now, I will bake them tomorrow.
    23 replies | 712 view(s)
  • weeple2000's Avatar
    03-06-2019, 04:02 PM
    So I was able to chamber a dummy. I didn't PC it or lube it at all. I just wanted to know if it would chamber. Beforehand I tried to stick the front of the boolit, the bore riding part, into the bore of the barrel. The nose didn't entirely enter...
    23 replies | 712 view(s)
  • weeple2000's Avatar
    03-05-2019, 02:36 PM
    I guess the next thing I'll do is load a dummy round before powder coating just to make sure it chambers. Then I'll try to PC just the bands using the water dip method.
    23 replies | 712 view(s)
  • weeple2000's Avatar
    03-05-2019, 01:14 AM
    Reading about this a bit I think that there are a couple things going on. A bore rider bullet is one that has the bands in the groove and the nose sits within the bore. So I think there are probably other bore rider designs where the boolit won't...
    23 replies | 712 view(s)
  • weeple2000's Avatar
    03-05-2019, 01:06 AM
    So I attempted to chamber a dummy round. It didn't go. I will try another dummy using the float method. The boolit in question is the Lee 200 in the OP.
    23 replies | 712 view(s)
  • weeple2000's Avatar
    03-04-2019, 12:36 AM
    Is tumble lube a better option for a bore rider then?
    23 replies | 712 view(s)
  • weeple2000's Avatar
    03-03-2019, 10:04 PM
    I understand that the Lee c309-200r is a bore rider. If I powder coat it I might have issues. If I load a dummy round, will I be good to go if it chambers?
    23 replies | 712 view(s)
  • weeple2000's Avatar
    02-21-2019, 12:07 PM
    You can find a toaster oven secondhand pretty cheap. I held out for a convention model because I heard those were a bit better.
    49 replies | 1763 view(s)
  • weeple2000's Avatar
    02-21-2019, 03:08 AM
    So I think I am having some success improving my PC system. This is what I came up with. I have a lot of these take out containers. I keep finding uses for them with reloading and casting. I did have a few boolits that stuck together end to...
    49 replies | 1763 view(s)
No More Results
About weeple2000

Basic Information

About weeple2000
Location:
Madison, WI

Statistics


Total Posts
Total Posts
109
Posts Per Day
0.40
General Information
Last Activity
03-20-2019 08:58 PM
Join Date
06-24-2018
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check