ADvertise hereMidSouth Shooters SupplyRotoMetals2Titan Reloading
Inline FabricationWidenersRepackboxLee Precision

Donate Now Goal amount for this year: 6000 USD, Received: 4555 USD (76%)
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


Tab Content
  • HATCH's Avatar
    Yesterday, 08:22 PM
    HATCH replied to a thread Help with PID in Casting Equipment
    If you measuring DC voltage then it would be safe to assume there is a issue with that PID. Sent from my iPhone using Tapatalk
    24 replies | 509 view(s)
  • HATCH's Avatar
    Yesterday, 05:28 PM
    HATCH replied to a thread Help with PID in Casting Equipment
    According to his model # it is a dc voltage output model for the SSR. Sent from my iPhone using Tapatalk
    24 replies | 509 view(s)
  • HATCH's Avatar
    08-10-2020, 12:50 PM
    According to the picture looks like 70 Sent from my iPhone using Tapatalk
    3 replies | 124 view(s)
  • HATCH's Avatar
    08-09-2020, 11:30 AM
    Bump. Have one ready to ship Will be ordering more pids/ssr tomorrow Sent from my iPhone using Tapatalk
    34 replies | 38141 view(s)
  • HATCH's Avatar
    08-09-2020, 11:30 AM
    Currently two weeks out Sent from my iPhone using Tapatalk
    26 replies | 9920 view(s)
  • HATCH's Avatar
    08-09-2020, 11:11 AM
    HATCH replied to a thread Help with PID in Casting Equipment
    I unsubscribed to this thread so if you need any additional help send me a PM Sent from my iPhone using Tapatalk
    24 replies | 509 view(s)
  • HATCH's Avatar
    08-07-2020, 09:20 PM
    HATCH replied to a thread Help with PID in Casting Equipment
    That inkbird will work. Please keep in mind that there is a very slight possibility that the PID May of been damaged by using the incorrect SSR but I am pretty sure itís gonna be ok. Sent from my iPhone using Tapatalk
    24 replies | 509 view(s)
  • HATCH's Avatar
    08-07-2020, 05:38 PM
    HATCH replied to a thread Help with PID in Casting Equipment
    Your getting bleed thru voltage but no current Get the correct ssr Sent from my iPhone using Tapatalk
    24 replies | 509 view(s)
  • HATCH's Avatar
    08-07-2020, 11:58 AM
    unless the item was sent priority mail or express mail all other forms of mailing are delayed. It took four days for a package to go from the main hub to my little post office. 14 miles of road travel and typically depending on arrival to the main...
    65 replies | 1580 view(s)
  • HATCH's Avatar
    08-07-2020, 09:27 AM
    HATCH replied to a thread Help with PID in Casting Equipment
    I think I got something Looking over closely at the SSR, I noticed something. That model SSR uses 90-280 VAC on the control side. I believe that model PID provided a @7 volt output for the SSR. That would explain why you aren't getting any...
    24 replies | 509 view(s)
  • HATCH's Avatar
    08-07-2020, 09:21 AM
    HATCH replied to a thread Help with PID in Casting Equipment
    looks like its wired up right. need to verify voltages. I ran into a issue a couple months ago which caused me to make a 90 min service call to visit a Master Caster Panel customer. The pot would never get up to temp. I checked my voltages and...
    24 replies | 509 view(s)
  • HATCH's Avatar
    08-06-2020, 05:30 PM
    HATCH replied to a thread Help with PID in Casting Equipment
    Can you take a picture of your setup? I found the manual -> https://www.instrumart.com/assets/Red-Lion-T48-P48-Manual.pdf You should have a SSR that you are using. For discussion we are gonna label the ssr as the picture below shows 1...
    24 replies | 509 view(s)
  • HATCH's Avatar
    07-15-2020, 05:33 PM
    Ok. I will send you a pm Sent from my iPhone using Tapatalk
    26 replies | 9920 view(s)
  • HATCH's Avatar
    07-15-2020, 05:13 PM
    Well itís expensive to ship to you. You can locate a third party shipper. Basically I ship to them in the US and they handle the overseas shipment. I think the last two panels I shipped directly to your continent cost around $350 in shipping...
    26 replies | 9920 view(s)
No More Results
About Dryb2860

Basic Information

About Dryb2860
Location:
Columbia, SC
Interests:
Shooting Sports, reloading, hunting, fishing, and golf
Occupation:
Emergency Management

Statistics


Total Posts
Total Posts
13
Posts Per Day
0.02
General Information
Last Activity
09-17-2018 07:42 PM
Join Date
06-04-2018
Referrals
0

1 Friend

  1. HATCH HATCH is offline

    Super Moderator

    HATCH
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check