WidenersRepackboxLee PrecisionTitan Reloading
RotoMetals2MidSouth Shooters SupplyInline Fabrication

Tab Content
  • sureYnot's Avatar
    Yesterday, 02:11 PM
    I have the same issue with a couple pistols. Maybe 3-4 out of 100 are too bulged to chamber. Solution was to run them PARTIALLY into the sizing die. Just enough to get them to plunk. This'll take the bulge out without ruining tension. If you...
    28 replies | 464 view(s)
  • sureYnot's Avatar
    05-18-2019, 08:00 PM
    I wouldn't have sized them. Just flared and loaded again. But, since you did lube and size, could you just wipe them off with a rag wetted in alcohol? Think that'd be my next move. Sent from my XT1710-02 using Tapatalk
    21 replies | 480 view(s)
  • sureYnot's Avatar
    05-16-2019, 01:08 PM
    I have no way to slug a .223 either. I arrived at .2265 by tinkering with all other variables until I found my most accurate load. Which would have been good for rabbits, but not squirrel heads. At that point I started sanding out my sizer .0005...
    29 replies | 755 view(s)
  • sureYnot's Avatar
    05-15-2019, 05:50 PM
    sureYnot replied to a thread New twist scam call in Our Town
    Not true at all. It costs them money.
    13 replies | 438 view(s)
  • sureYnot's Avatar
    05-15-2019, 09:34 AM
    Your logic is sound. Sent from my XT1710-02 using Tapatalk
    29 replies | 755 view(s)
  • sureYnot's Avatar
    05-15-2019, 07:47 AM
    I can't tell you why. I hope someone smarter comes along and explains. But I can testify that it is so. I have to size mine to .2265 before they're worth shooting through my rifle. Meanwhile, .224 jacketed have the same accuracy. .224 cast will...
    29 replies | 755 view(s)
  • sureYnot's Avatar
    05-13-2019, 03:30 PM
    sureYnot replied to a thread Today's best deals: in Our Town
    Powder Valley post from Facebook six hours ago: Get yourself geared up for a FREE HAZMAT tomorrow 05/14! Sent from my XT1710-02 using Tapatalk
    159 replies | 19213 view(s)
  • sureYnot's Avatar
    05-12-2019, 11:21 AM
    Forgot OP mentioned 9mm. (Was being pestered while posting.) I load 9mm with same alloy, treated at 425. Any softer and the brass swages down the bullet. 150 grains over 2.8 of either titegroup or promo. Promo is right at max. My Ruger likes...
    29 replies | 755 view(s)
  • sureYnot's Avatar
    05-12-2019, 09:36 AM
    Depends on what you're trying to make it do. Gas check or no? Powder coat or no? Barrel twist? Bullet weight? I mix coww and range scrap 50/50 and add 1% tin. Powder coat. 62 grain. Plain base, no gas check. Heat treated at 450 (very...
    29 replies | 755 view(s)
  • sureYnot's Avatar
    05-11-2019, 09:48 PM
    I use OpenOffice. It is freeware and works very well. Sent from my XT1710-02 using Tapatalk
    14 replies | 567 view(s)
  • sureYnot's Avatar
    05-08-2019, 07:22 PM
    Think you spelled chemistry wrong. Sent from my XT1710-02 using Tapatalk
    62 replies | 2005 view(s)
  • sureYnot's Avatar
    05-08-2019, 03:03 PM
    Agreed. I use bacon grease to make popcorn in the cast iron skillet. It's awesome. Pretty much anything fried gets bacon flavor. Burgers, potatoes, carrots... There's no limit to the power of bacon. Sent from my XT1710-02 using Tapatalk
    21 replies | 501 view(s)
  • sureYnot's Avatar
    05-02-2019, 07:41 PM
    sureYnot replied to a thread t in Testing Area
    Imgur has a button for forum sharing.
    1 replies | 199 view(s)
  • sureYnot's Avatar
    05-01-2019, 08:51 PM
    Very nice. Sent from my XT1710-02 using Tapatalk
    42 replies | 1190 view(s)
  • sureYnot's Avatar
    04-26-2019, 12:53 PM
    When I was in junior high, my dad shot a couple fifty cents pieces at fifty yards with open sights to prove a point to one of my know-it-all teachers. (A character in a story we were reading made an impressive shot. Teacher immediately declared it...
    68 replies | 10137 view(s)
More Activity
About sureYnot

Basic Information

About sureYnot
Location:
Central Minnesota (Brainerd Lakes area)

Statistics


Total Posts
Total Posts
309
Posts Per Day
0.87
General Information
Last Activity
Today 01:38 PM
Current Activity
Viewing Thread PSA Stripped Lowers
Join Date
06-01-2018
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check