MidSouth Shooters SupplyWidenersLee PrecisionTitan Reloading
ADvertise hereInline FabricationRepackboxRotoMetals2

  • shell70634's Avatar
    06-03-2020, 10:09 PM
    Make sure the ejector rod hasn't un screwed a bit too.
    13 replies | 306 view(s)
  • clodhopper's Avatar
    06-03-2020, 12:41 AM
    clodhopper replied to a thread Core molds in Swaging
    The paper gives .0015 fudge room on both sides of center. So if your hole is off center just a little bit, the casting will still fall out of the mold. When you remove the paper the cavity is reduced in volume.
    10 replies | 672 view(s)
  • shell70634's Avatar
    06-02-2020, 06:24 PM
    #03. Not packaged but appears unused. #18. New in package #10. New in package #6. New in package All for $50.00 shipped. Will take cash, money order, PP F&F, or prime rib.
    1 replies | 104 view(s)
  • clodhopper's Avatar
    06-01-2020, 11:22 PM
    clodhopper replied to a thread Core molds in Swaging
    You could drill holes ok, but if the holes are not centered on the parting line of the blocks the cores do not want to fall out. Don't mount the blocks on the handles until after drilling the cavities. The fasteners are cleverly designed to not...
    10 replies | 672 view(s)
  • clodhopper's Avatar
    06-01-2020, 08:43 PM
    clodhopper replied to a thread Core molds in Swaging
    Charts for calculating weight of cores are here. www.castboolits.gunloads.com/showthread.php?276943-A-Little-Math-That-Will-HOPEFULLY-Be-Helpful Post #8 is where Gitano helped a lot. You still have to do some math. I have cut a few core molds on...
    10 replies | 672 view(s)
  • shell70634's Avatar
    06-01-2020, 03:25 PM
    I'll take em. PM to follow. Shelly
    1 replies | 148 view(s)
  • clodhopper's Avatar
    05-24-2020, 11:07 PM
    This question comes up so often. Brass is a little harder than copper, but compared to steel, brass is soft. Hot copper is sticky, but the addition of zinc makes brass comparatively slick. Most bullets are jacketed with gilding metal, which...
    13 replies | 1222 view(s)
  • shell70634's Avatar
    05-19-2020, 07:35 PM
    Before posting any pics I open them with the Paint program on my computer and resize them. Most from my phone are 4000 x 3000 or so pixels. I resize to 1000 or less, then crop, then save. They load up much quicker for me. I'm not computer...
    3 replies | 818 view(s)
  • clodhopper's Avatar
    05-16-2020, 06:23 PM
    Good looking bullets.
    13 replies | 1222 view(s)
  • shell70634's Avatar
    05-16-2020, 01:03 PM
    My daughter had 20 or so stolen in east Texas about 5 years ago. They've gotten 5 or 6 back. One from Ohio. The SO gave them back within a couple days of receiving them. Still looking for the rest.
    68 replies | 1897 view(s)
  • clodhopper's Avatar
    05-14-2020, 11:47 PM
    clodhopper replied to a thread Joining an airgun forum in AirGuns
    Bob Strene is on many forums, even castboolits.gunloads.com
    12 replies | 2137 view(s)
  • clodhopper's Avatar
    05-13-2020, 03:50 PM
    I was using a lyman big dipper until the heating coil burned out. Strongly considering Turning some scrap aluminum to fit tight, and fill the bottom half of the pot.
    21 replies | 771 view(s)
  • shell70634's Avatar
    05-11-2020, 04:19 PM
    I'll take it. PM follows Shelly
    1 replies | 666 view(s)
No More Results
About clodhopper

Basic Information

Date of Birth
December 29, 1955 (64)
About clodhopper
Biography:
shooting enthusiast
Location:
Bozoland Mt.
Interests:
Shoot steel shoot paper shoot gophers tip over a deer every now and then
Occupation:
make log homes

Signature


To lazy to chase arrows.
Clodhopper

Statistics


Total Posts
Total Posts
1,578
Posts Per Day
0.35
General Information
Last Activity
Today 08:00 AM
Join Date
02-28-2008
Referrals
3

8 Friends

  1. *Paladin* *Paladin* is offline

    Boolit Buddy

    *Paladin*
  2. marteeson marteeson is offline

    Boolit Mold

    marteeson
  3. Mtman314 Mtman314 is offline

    Boolit Buddy

    Mtman314
  4. muzzlebuster muzzlebuster is offline

    Boolit Mold

    muzzlebuster
  5. rjathon rjathon is offline

    Boolit Buddy

    rjathon
  6. shadowcaster shadowcaster is offline

    Boolit Buddy

    shadowcaster
  7. shell70634 shell70634 is offline

    Boolit Buddy

    shell70634
  8. wildwes wildwes is offline

    Boolit Bub

    wildwes
Showing Friends 1 to 8 of 8
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check