ADvertise hereInline FabricationLee PrecisionRepackbox
RotoMetals2MidSouth Shooters SupplyTitan ReloadingWideners

Donate Now Goal amount for this year: 6000 USD, Received: 4280 USD (71%)
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


Tab Content
  • HATCH's Avatar
    Today, 05:28 PM
    HATCH replied to a thread Help with PID in Casting Equipment
    According to his model # it is a dc voltage output model for the SSR. Sent from my iPhone using Tapatalk
    21 replies | 444 view(s)
  • HATCH's Avatar
    Yesterday, 12:50 PM
    According to the picture looks like 70 Sent from my iPhone using Tapatalk
    3 replies | 120 view(s)
  • HATCH's Avatar
    08-09-2020, 11:30 AM
    Bump. Have one ready to ship Will be ordering more pids/ssr tomorrow Sent from my iPhone using Tapatalk
    34 replies | 38130 view(s)
  • HATCH's Avatar
    08-09-2020, 11:30 AM
    Currently two weeks out Sent from my iPhone using Tapatalk
    26 replies | 9917 view(s)
  • HATCH's Avatar
    08-09-2020, 11:11 AM
    HATCH replied to a thread Help with PID in Casting Equipment
    I unsubscribed to this thread so if you need any additional help send me a PM Sent from my iPhone using Tapatalk
    21 replies | 444 view(s)
  • HATCH's Avatar
    08-07-2020, 09:20 PM
    HATCH replied to a thread Help with PID in Casting Equipment
    That inkbird will work. Please keep in mind that there is a very slight possibility that the PID May of been damaged by using the incorrect SSR but I am pretty sure itís gonna be ok. Sent from my iPhone using Tapatalk
    21 replies | 444 view(s)
  • HATCH's Avatar
    08-07-2020, 05:38 PM
    HATCH replied to a thread Help with PID in Casting Equipment
    Your getting bleed thru voltage but no current Get the correct ssr Sent from my iPhone using Tapatalk
    21 replies | 444 view(s)
  • HATCH's Avatar
    08-07-2020, 11:58 AM
    unless the item was sent priority mail or express mail all other forms of mailing are delayed. It took four days for a package to go from the main hub to my little post office. 14 miles of road travel and typically depending on arrival to the main...
    65 replies | 1542 view(s)
  • HATCH's Avatar
    08-07-2020, 09:27 AM
    HATCH replied to a thread Help with PID in Casting Equipment
    I think I got something Looking over closely at the SSR, I noticed something. That model SSR uses 90-280 VAC on the control side. I believe that model PID provided a @7 volt output for the SSR. That would explain why you aren't getting any...
    21 replies | 444 view(s)
  • HATCH's Avatar
    08-07-2020, 09:21 AM
    HATCH replied to a thread Help with PID in Casting Equipment
    looks like its wired up right. need to verify voltages. I ran into a issue a couple months ago which caused me to make a 90 min service call to visit a Master Caster Panel customer. The pot would never get up to temp. I checked my voltages and...
    21 replies | 444 view(s)
  • HATCH's Avatar
    08-06-2020, 05:30 PM
    HATCH replied to a thread Help with PID in Casting Equipment
    Can you take a picture of your setup? I found the manual -> https://www.instrumart.com/assets/Red-Lion-T48-P48-Manual.pdf You should have a SSR that you are using. For discussion we are gonna label the ssr as the picture below shows 1...
    21 replies | 444 view(s)
  • HATCH's Avatar
    07-15-2020, 05:33 PM
    Ok. I will send you a pm Sent from my iPhone using Tapatalk
    26 replies | 9917 view(s)
  • HATCH's Avatar
    07-15-2020, 05:13 PM
    Well itís expensive to ship to you. You can locate a third party shipper. Basically I ship to them in the US and they handle the overseas shipment. I think the last two panels I shipped directly to your continent cost around $350 in shipping...
    26 replies | 9917 view(s)
No More Results
About Y-Nots3D

Basic Information

About Y-Nots3D
Biography:
Self Employed Ex military, Entrepreneur
Location:
Virginia
Interests:
Design ,Racing , Guns
Occupation:
Entrepreneur

Statistics


Total Posts
Total Posts
0
Posts Per Day
0
General Information
Last Activity
03-05-2018 01:25 PM
Join Date
02-07-2018
Referrals
0
Home Page
https://www.facebook.com/Ynots3DDDCreations

1 Friend

  1. HATCH HATCH is offline

    Super Moderator

    HATCH
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check