WidenersRepackboxInline FabricationMidSouth Shooters Supply
RotoMetals2Lee PrecisionTitan Reloading

  • GregLaROCHE's Avatar
    Yesterday, 09:56 PM
    Was it down for a second time?
    7 replies | 259 view(s)
  • GregLaROCHE's Avatar
    Yesterday, 09:51 PM
    Figuring out a gun is a lot easier than figuring out a woman!
    15 replies | 487 view(s)
  • GregLaROCHE's Avatar
    Yesterday, 09:43 PM
    The right thing to do. Now you have to take the responsibility of teaching him how to use it correctly and safely. Supervise it. When I was twelve I did some unsupervised things with guns that weren’t always the safest.
    11 replies | 387 view(s)
  • GregLaROCHE's Avatar
    Yesterday, 09:23 PM
    GregLaROCHE replied to a thread burnt patches? in Muzzleloading.
    Does anyone use cream of wheat on top of powder ?
    40 replies | 887 view(s)
  • GregLaROCHE's Avatar
    Yesterday, 09:05 PM
    Opioids never seemed to help me that much. For short term pain, when I had a hip replacement, Ice was by far the best. I’ve suffered with arthritis for years and Celebrex works miracles for me. If I forget to take it one morning, I sure know it. It...
    41 replies | 820 view(s)
  • GregLaROCHE's Avatar
    Yesterday, 08:48 PM
    My 30 cal carbine made by Rockola. It was stolen, so I can’t blame myself, but I really liked it. It would only chamber ball rounds consistently though.
    29 replies | 363 view(s)
  • GregLaROCHE's Avatar
    Yesterday, 08:40 PM
    French 1777 flintlock Dragon. Built in 1815. Didn’t go through the wars that many of the older models did, therefore in much better condition. I still had to spend a lot of time going through it to get it as close to new as possible. I plan to shoot...
    1665 replies | 181945 view(s)
  • GregLaROCHE's Avatar
    Yesterday, 08:26 PM
    Talking about accuracy, is length more important in a smooth bore BP gun than in a rifled muzzle loader or cartridge gun? I know a lot of old military flintlocks where long, but always thought that was so the second line of shooters could shoot...
    2 replies | 48 view(s)
  • GregLaROCHE's Avatar
    06-16-2019, 07:46 PM
    I’ve learned a lot during this post. I recuperate a lot of lead from an indoor range. At the beginning of this post I was thinking, why not see what I can get from the trap range. Now I think I just better let it pass.
    35 replies | 3487 view(s)
  • GregLaROCHE's Avatar
    06-15-2019, 05:26 PM
    GregLaROCHE replied to a thread What is it in Cast Boolits
    The original Crescent Hammer.
    16 replies | 796 view(s)
  • GregLaROCHE's Avatar
    06-15-2019, 05:22 PM
    Were you tumbling only the boolits and not the loaded cartridge ? If so did they come out concentric and with the diameter you wanted?
    5 replies | 302 view(s)
  • GregLaROCHE's Avatar
    06-15-2019, 09:44 AM
    I agree with all the above. Lacquer isn’t a tough finish. I think most industrial furniture produced today is coated with polyethylene. If you’re just planning to use the gun as a wall hanger it should serve well, but any exposure to water it will...
    23 replies | 628 view(s)
  • GregLaROCHE's Avatar
    06-15-2019, 09:31 AM
    I’ve always heard that arsenic was used in casting shot. If I were melting it, I would make sure I was up wind from the fumes. Not sure if the amount present would be harmful, but it doesn’t hurt to play it safe.
    35 replies | 3487 view(s)
  • GregLaROCHE's Avatar
    06-12-2019, 11:07 AM
    I just saw this and thought I would post it. Please don’t consider me from on side or the other. https://www.cnn.com/2019/06/12/health/glyphosate-cereals-ewg-study/index.html
    36 replies | 882 view(s)
  • GregLaROCHE's Avatar
    06-10-2019, 06:33 PM
    I had a Lee universal expander, but quickly changed to some from NOE. They’re more precise and I think they help extend brass life.
    5 replies | 146 view(s)
  • GregLaROCHE's Avatar
    06-10-2019, 04:14 PM
    Why would you want to do it? A .45/70 is enough gun for North America, including Alaska. Sell or keep it and buy another gun, if that’s really what you want.
    29 replies | 937 view(s)
  • GregLaROCHE's Avatar
    06-10-2019, 03:59 PM
    Sounds like adding more tin and lowering he pot temperature would be the first thing to try. Lee’s moulds aren’t always perfect. You can always try sending it back or hone it a little bit with a split dowel and fine sandpaper.
    33 replies | 720 view(s)
  • GregLaROCHE's Avatar
    06-10-2019, 03:36 PM
    Iíve been looking at NOEs bushings. I have a bunch of there bushings already. I have always bought the body sizer bushings. Now I want to size down more than the body sizer they have listed, but they have a smaller one in nose sizer. Do nose sizers...
    1 replies | 146 view(s)
  • GregLaROCHE's Avatar
    06-08-2019, 12:21 PM
    I agree the loss of game probably has a lot to do with, loss of habitats most of all. Probably other things too. The world population is putting a strain on all food supplies. Both land and sea. The agricultural industry is forced to produce the...
    36 replies | 882 view(s)
  • GregLaROCHE's Avatar
    06-08-2019, 08:50 AM
    Fooled me. I thought you were going to say you went in for milk and came out with a new gun! A little mold on cheese dose not mean the end of the world. A lot of cheese makers look for it to improve the taste of there cheese. That’s what most...
    18 replies | 723 view(s)
  • GregLaROCHE's Avatar
    06-08-2019, 08:33 AM
    Oh boy that looks good! I often add sausage meat to other meats and I like low heat slow cooked.
    18 replies | 364 view(s)
  • GregLaROCHE's Avatar
    06-08-2019, 08:24 AM
    GregLaROCHE replied to a thread Is it a Boolit if in Cast Boolits
    I always thought a gas check still was considered a boolit. You still have to lube or PC it. Are there any competitions that say lead boolits only? What do they say about gas checks?
    20 replies | 510 view(s)
  • GregLaROCHE's Avatar
    06-07-2019, 02:49 PM
    I hear what you are saying, I donít think you are comparing apples to apples. Crankshafts run on a cushion of oil and normally shouldnít touch the Babbitt.
    36 replies | 1268 view(s)
  • GregLaROCHE's Avatar
    06-07-2019, 02:41 PM
    This really should be a two part question. The throat and the rest of the barrel. Given the same power loads for the cartridges, throat wear should be the same. There are rounds known as barrel burners, but I am pretty sure that’s mostly the...
    36 replies | 1268 view(s)
  • GregLaROCHE's Avatar
    06-07-2019, 01:41 PM
    I used to use them a lot, but less and less that we are finding out that they can be harmful. Still I use some now and then. I believe, live a better life with the use of chemicals. I have a lot around my place. My favorite is HCl on heavy rust (not...
    36 replies | 882 view(s)
  • GregLaROCHE's Avatar
    06-07-2019, 01:28 PM
    I have a Lyman turret press I bought new in the eighties. For over twenty five years, I have always wanted a Rock Chucker. A couple of years ago I saw a new one for sale cheap on eBay. I thought it would become my main press. In reality, I seldom...
    48 replies | 1312 view(s)
  • GregLaROCHE's Avatar
    06-07-2019, 12:59 PM
    From what I’m hearing, I’m leaning towards brass. If you’re buying a mould other than from Lee, the additional cost of brass doesn’t to be that much. I’m planning on two cavities, so weight shouldn’t be too much of a problem, however, one of the...
    20 replies | 514 view(s)
  • GregLaROCHE's Avatar
    06-06-2019, 05:01 AM
    Do they make moulds out of stainless steel?
    20 replies | 514 view(s)
More Activity
About GregLaROCHE

Basic Information

Statistics


Total Posts
Total Posts
900
Posts Per Day
1.81
General Information
Last Activity
Today 04:23 AM
Join Date
02-06-2018
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check