MidSouth Shooters SupplyLee PrecisionADvertise hereTitan Reloading
RepackboxRotoMetals2Inline Fabrication

Donate Now Goal amount for this year: 6000 USD, Received: 6135 USD (102%)
OUR GOAL HAS BEEN MET!
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


Tab Content
  • cwtebay's Avatar
    Today, 11:45 AM
    I have used H1000 forever in 7mag with 160 gr bullets. But I have been messing with RL22 lately with great results also. Sent from my Pixel 3 XL using Tapatalk
    3 replies | 52 view(s)
  • cwtebay's Avatar
    09-13-2019, 11:12 PM
    I have 1892's and SAA in both. Pick the one that turns your crank. They're both great cartridges to reload, brass and loaded ammo is available for both. You can't go wrong with your choice!! Sent from my Pixel 3 XL using Tapatalk
    25 replies | 567 view(s)
  • cwtebay's Avatar
    09-11-2019, 09:18 PM
    cwtebay replied to a thread 30 WCF Die in Reloading Equipment
    At the time I was reloading for 14 - 30-30 firearms. I had difficulty with neck sizing due to the variety, and asked Redding what I should do. They suggested the body die and I came with the crimp die because the bullets started moving with...
    22 replies | 557 view(s)
  • cwtebay's Avatar
    09-11-2019, 09:41 AM
    I wouldn't be that concerned about the primers, but dump the powder. But going to square one by depriming and salvaging the brass would be the most prudent. Sent from my Pixel 3 XL using Tapatalk
    7 replies | 239 view(s)
  • cwtebay's Avatar
    09-10-2019, 10:16 PM
    cwtebay replied to a thread 30 WCF Die in Reloading Equipment
    I have used Redding body dies for the same. I don't know how neck life can suffer unless oversize jacketed projectiles are used - I've used them for 10+ reloads now on Winchester brass. I do size to bullet diameter using lanolin in the neck and use...
    22 replies | 557 view(s)
  • cwtebay's Avatar
    09-10-2019, 10:11 PM
    That's a little crazy for my taste. I've never seen any factory load data, and I'm quite sure that whomever told you that hasn't either. The cents in powder isn't worth your safety or life. Sent from my Pixel 3 XL using Tapatalk
    7 replies | 239 view(s)
  • cwtebay's Avatar
    09-10-2019, 05:45 PM
    cwtebay replied to a thread Cheek piece riser in Leverguns
    I use the elastic from a cut off sock to trap pieces of foam under on top of the comb to get the right cheek height for my young sons. There is also a kit available that does the same. Sent from my Pixel 3 XL using Tapatalk
    8 replies | 309 view(s)
  • cwtebay's Avatar
    09-05-2019, 10:08 AM
    cwtebay replied to a thread Rossi 92 rebarrel in Leverguns
    I second Rimfires post. I had a shot out original 92 lined to 44 WCF with awesome results. I believe Randy's Custom Rifles in Wyoming did the work. Sent from my Pixel 3 XL using Tapatalk
    6 replies | 329 view(s)
  • cwtebay's Avatar
    08-31-2019, 09:47 PM
    Kinda depressing! I always held out for them to reopen. Sent from my Pixel 3 XL using Tapatalk
    8 replies | 679 view(s)
  • cwtebay's Avatar
    08-30-2019, 08:53 PM
    cwtebay replied to a thread 35/30 makes me smile in Leverguns
    Yes, I've done nothing but use Lee neck sizing on my venture. I am around 1200 rounds through it, trimmed a bit, but I'm not shooting the brass in anything else - so neck sizing seems to be good for me. Step 1: prime and charge brass with your...
    62 replies | 2880 view(s)
  • cwtebay's Avatar
    08-24-2019, 11:46 PM
    cwtebay replied to a thread 35/30 makes me smile in Leverguns
    Do you have problems before firing 3-4 times? I noticed that chamber dimensions varied wildly on 35/30 aka 35- 30/30 (depending upon n the smith who performed the change) when I first started loading for it, and I heard everything from COW and...
    62 replies | 2880 view(s)
  • cwtebay's Avatar
    08-23-2019, 10:39 AM
    I believe those are teat fire cartridges. The ones I have seen are 32 caliber. They were made for a revolver I think, and likely others. Cool transition design! Sent from my Pixel 3 XL using Tapatalk
    7 replies | 477 view(s)
No More Results
About cwtebay

Basic Information

Date of Birth
March 6, 1975 (44)

Statistics


Total Posts
Total Posts
182
Posts Per Day
0.30
General Information
Last Activity
Today 12:45 PM
Join Date
01-27-2018
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check