Lee PrecisionADvertise hereInline FabricationRotoMetals2
Titan ReloadingMidSouth Shooters SupplyRepackboxWideners

Tab Content
  • pashiner's Avatar
    05-12-2020, 12:55 PM
    i use cci standard velocity in everything. it's subsonic, so a bit quieter, and is way more consistent than other brands through my guns. my Ruger mk2 LOVES it.
    18 replies | 1247 view(s)
  • pashiner's Avatar
    05-11-2020, 01:03 PM
    I'll give the grendel a vote. there's plenty of 7.63x39 brass to pick up at my local range, and they're just a full length size and 1 reload away from being fine grendel brass with big primers to boot. (300 can be made from .223 with some more...
    33 replies | 1044 view(s)
  • pashiner's Avatar
    05-11-2020, 10:36 AM
    my vote (in this hypothetical business) goes to a hardcast .690 ball loaded inside a 12 gauge shotcup. Booger the ball up real good by rolling it around on a sidewalk before you load it, and burn the plastic shell after the shooting, or ditch it at...
    51 replies | 16653 view(s)
  • pashiner's Avatar
    05-11-2020, 09:42 AM
    I was a little concerned about the toughness of your toilet ring wax/olive oil mix (yes, a fine boolit lube). I've had better luck with harder wax. I use the big white dollar store candles that break into granular pieces when you smash them. I...
    18 replies | 5206 view(s)
  • pashiner's Avatar
    05-07-2020, 01:00 PM
    12 gauge shotgun shells full of corn meal, grits, or rice are my go-to for stinging swarming insects. You can get quite a payload in those things if you cut down the wad to just a gas seal, and then reduce the powder charge by about half. I know...
    30 replies | 2110 view(s)
  • pashiner's Avatar
    05-06-2020, 01:02 PM
    I've been tossing around the idea of a poor-man's ball mill for making cast lead balls more perfectly round. At the moment it's just an old freon tank with a hole in it. I pour in a load of balls, seal the hole and let it crash around in the back...
    35 replies | 7994 view(s)
  • pashiner's Avatar
    05-01-2020, 08:49 AM
    Your factory barrel for the 870 is likely sufficient for shooting any slug you like outto 50 yards with the right choke tube. A short smoothbore barrel with sights is good for "tactical" applications, but may not be cut for chokes, so there isn't...
    20 replies | 748 view(s)
No More Results
About pashiner

Basic Information

About pashiner
Biography:
I like things that go bang. Unless it's a motor...those shouldn't make that noise.
Location:
Pennsylvania
Interests:
Shootin' fishin' wrenchin' and guitar pickin'
Occupation:
Mechanic

Statistics


Total Posts
Total Posts
91
Posts Per Day
0.10
General Information
Last Activity
Today 03:42 PM
Join Date
12-28-2017
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check