MidSouth Shooters SupplyRepackboxGraf & SonsInline Fabrication
StainLess Steel MediaWidenersRotoMetals2

Tab Content
  • john.k's Avatar
    12-11-2018, 04:15 PM
    ...45/70 adaptors have never been a goer in a 577/450 because the the case extends into the thin neck section of the adaptor.........the Colt 45 adaptors work OK as a mechanism,but the bullets are way too small for the Martini bore.......a far more...
    22 replies | 1294 view(s)
  • john.k's Avatar
    12-09-2018, 09:52 PM
    I had a primer go off once broke the big hotplate on the wood stove,and the case put a dent in the roof above.The noise was deafening.Frightened the life out of me.....found out later the bullet was explosive,and I had pulled it in the vise.
    58 replies | 2194 view(s)
  • john.k's Avatar
    12-09-2018, 09:44 PM
    I had a primer go off in the press.......the old cat was sleeping curled up just behind,and he didnt move.....seems he either didnt hear it,or didnt register .......My worry with primers popping is that one of the nervous neighbours will drop a dime...
    58 replies | 2194 view(s)
  • john.k's Avatar
    12-08-2018, 08:38 PM
    Anyone tried loctite on lee molds?
    14 replies | 368 view(s)
  • john.k's Avatar
    12-08-2018, 08:35 PM
    i find if you lube the mould pivots with bees wax,after a while the stuff carbonizes and sticks the sprue screw tight......no more issues............its possible a spot of loctite would do too....loctite does soften with heat,but it stays sticky,so...
    17 replies | 543 view(s)
  • john.k's Avatar
    12-08-2018, 06:27 PM
    Caterpillar make bolts with the whole head covered in lines.............Cat bolts are usually easy to machine too,unlike the Chinese Gr 8 bolts that are very hard................incidentally,we found the Chinese Gr8 bolts very prone to fracture...
    36 replies | 1634 view(s)
  • john.k's Avatar
    12-07-2018, 08:51 PM
    I suspect the 1 in 38 twist was chosen by Benjamin Henry in 1860 for the new 44 rimfire.For a 200 grain bullet powered by blackpowder the shallow groove and slow twist was needed to control fouling......As often happens,when the changeover to CF...
    28 replies | 760 view(s)
  • john.k's Avatar
    12-06-2018, 10:36 PM
    Ive seen a few of them.......pretty typical of absolute cheapest level of chinese cast........the iron is OK,but sometimes the cast contains large blowholes ,which weaken and cause breakage.........probably made on very basic and worn tools........I...
    12 replies | 565 view(s)
  • john.k's Avatar
    12-03-2018, 10:55 PM
    Looks like a workable alloy is 88/12 tin,so cost would be $20 lb,with no scrap available either.The other problem I see is the metal expands on cooling,meaning bullets may stick tightly in mold cavities......As to ingots breaking apart,lead does...
    27 replies | 726 view(s)
  • john.k's Avatar
    12-02-2018, 09:23 PM
    Most of the older 44-40 s have such tight necks,that bullets over 429 wont chamber ,even in thin Winchester made brass.In fact one of my 94 s is so tight a 429 bullet will seat tightly in a fired case.No sizing required.Bore size is 423-427...
    15 replies | 489 view(s)
  • john.k's Avatar
    12-02-2018, 09:16 PM
    Altering 94 feed guides is a shortcut to a single shot...Very tricky,unless you have examples to copy ,or the factory drawings...And spares for the 44s were rare ,even when the guns were current.I tried to alter a 44 mag to 44-40 using a new 92...
    19 replies | 894 view(s)
  • john.k's Avatar
    12-02-2018, 05:53 AM
    The arabs eat camels,and you can see whats happened to them...We shoot horses too,but ive never eaten one (knowingly)....dont like venison either,dry and tasteless...........now goat and rabbit,youve got something cookin...........Did you know if...
    35 replies | 2690 view(s)
  • john.k's Avatar
    11-27-2018, 08:21 PM
    if you can buy a lifter and a set of feed guides for the 44-40 version,then you might have a chance.......otherwise Im sure you would end up with a single shot.
    19 replies | 894 view(s)
  • john.k's Avatar
    11-25-2018, 10:20 PM
    I have sleeved chambers ,but it does leave a tiny,maybe near invisible gap,and I have always advised shooters to not use blackpowder for fear of corrosion..........Am I wrong....is a sleeve ok with the fouling?
    13 replies | 499 view(s)
  • john.k's Avatar
    11-25-2018, 01:46 AM
    john.k replied to a thread Lathe manual parts list in Our Town
    broken teeth on the back gears near always caused by attempting to remove stuck threaded chucks.sometimes the threads can be very hard to move,and the temptation is to put a long Crescent wrench on the jaws,and apply much force,or worse using a...
    4 replies | 299 view(s)
  • john.k's Avatar
    11-22-2018, 06:54 AM
    if the powder has started to detiorate,the tin will be rusty inside............Ive ony ever had 4895 go bad,turned into red dust entirely.....wasnt surplus either ,was IMR 4895 in a Du Pont tin.......funny thing is cordite seems to last...
    21 replies | 4089 view(s)
  • john.k's Avatar
    11-22-2018, 02:51 AM
    john.k replied to a thread New Barrel in Factory Rifles
    Yeah now everyone can closely inspect their bore.....makers have got to be lot more careful,or back it comes.....reminds me of years ago at work.......sand blasting pipe internals...........boss says..."just do the ends ---they cant see...
    14 replies | 566 view(s)
  • john.k's Avatar
    11-22-2018, 02:43 AM
    Just a variation on a 22.....most 22s have the handle halfway along,so it can lock in a convenient spot......nothing special IMHO........yeah,some experts on that forum.....Pics couldnt be much less use either.
    11 replies | 835 view(s)
  • john.k's Avatar
    11-22-2018, 02:33 AM
    A young guy shooting a Lithgow smelly at the range came up to me ...."How can I get the bolt out?"...I was surprised ,but I showed him and his girlfriend........Then he tried it,and still couldnt get the bolt out....he couldnt get a grip on the...
    35 replies | 2690 view(s)
  • john.k's Avatar
    11-20-2018, 08:03 PM
    NHS is correct,first break the grip of the case on primer,sometimes sealer too,and the hydraulic method will move them......but not if there is a heavy crimp ......Once the military primer is gone,reloaded primers blow out easily..........I...
    81 replies | 92857 view(s)
  • john.k's Avatar
    11-19-2018, 07:04 PM
    I suspect the project would be problematic.........I know Winchester had a lot of trouble getting the 94 to feed reliably in 44-40 and 44 mag back in the 70s.I also know that fiddling with the feed guides is a job for an expert.....which is someone...
    19 replies | 894 view(s)
  • john.k's Avatar
    11-19-2018, 09:28 AM
    Will a 45 fit in a 30-30 magazine tube.?..........not a big difference,about 006.........if the rim fits,its do able IMHO,the other issue would be the dovetails in the barrel making the rebored barrel too thin in wall thickness.
    19 replies | 894 view(s)
  • john.k's Avatar
    11-19-2018, 09:04 AM
    For the same reason copper dissolves in mercury .....at room temperature.
    38 replies | 1972 view(s)
  • john.k's Avatar
    11-17-2018, 02:58 AM
    There is no point using zinc for shot,as steel has a higher sg. and is much cheaper.....Same goes for bullets,steel is the cheapest substitute for bullets,just needs a hard barrel.Which is why just about every AK bullet fired outside the US is steel...
    19 replies | 724 view(s)
  • john.k's Avatar
    11-17-2018, 12:36 AM
    I didnt believe the candle flame story,not enough heat,I thought.............however the first case I tried ended up so soft it collapsed in the lee collet die.......But it is slow,and does leave the cases black.......Alcohol lamp would be...
    34 replies | 1382 view(s)
  • john.k's Avatar
    11-14-2018, 03:02 AM
    far from the worst.....dozens of fatal injuries from pulling shotguns out of cars,through fences,or guns propped up and falling over.One and both legs off at the knee from a gun in the back seat of a car.,gut shot pulling a gun in a blanket out of...
    45 replies | 2430 view(s)
No More Results
About john.k

Basic Information

About john.k
Biography:
retired mechanic/engineer.
Location:
brisbane ,qld,australia
Interests:
shooting,machinery,bikes
Occupation:
retired

Statistics


Total Posts
Total Posts
588
Posts Per Day
1.45
General Information
Last Activity
Today 01:17 AM
Join Date
11-01-2017
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check