RepackboxGraf & SonsInline FabricationWideners
StainLess Steel MediaRotoMetals2MidSouth Shooters Supply

Tab Content
  • marek313's Avatar
    Yesterday, 10:36 AM
    marek313 replied to a thread LEE mold for 10mm? in Cast Boolits
    One more vote for Lee 401-175-TC. Works great in my RIA Tac Ultra 10mm.
    9 replies | 143 view(s)
  • marek313's Avatar
    11-29-2018, 11:56 AM
    marek313 replied to a thread Fixed 1 Computer Problem in Our Town
    There is only one situation in which kicking a computer might make it work again. That is if you have standard hard drive and reading head gets stuck or doesnt reset home correctly. That might make it work again for short while and I mean very short...
    12 replies | 479 view(s)
  • marek313's Avatar
    11-27-2018, 03:35 PM
    I'll take NOE 358 155 TC $55 shipped. PM on the way
    7 replies | 968 view(s)
  • marek313's Avatar
    11-27-2018, 03:28 PM
    I pull any solder that i find at my scrap yard so I have some of those rods as well but i never figured out the tin content. I found many 50/50 bars but these thin ones have no markings. I figured it had to be worth at least $1/lb so I grab any...
    6 replies | 333 view(s)
  • marek313's Avatar
    11-20-2018, 06:05 PM
    Not every 9mm will chamber .357 as many have tight throats. You might need to get that guns throat reamed. That will allow you to chamber .357 seated to any length. Dougguy here can do it for you. He does fine work and he'll even put a crown cut on...
    10 replies | 358 view(s)
  • marek313's Avatar
    11-20-2018, 10:48 AM
    Thanx for all the info guys. Reading all the replies I also started thinking where the best location in the house for a gun safe would be. I would like to have it in the bedroom but I dont really have any room in there or room in the closet for...
    25 replies | 934 view(s)
  • marek313's Avatar
    11-19-2018, 05:25 PM
    Not sure if this is the right forum for this but I'm looking to purchase new gun safe. I dont need anything very large 12 gun would be more then big enough for my needs. My problem is that looking around web seems like most of the safes these days...
    25 replies | 934 view(s)
  • marek313's Avatar
    11-19-2018, 02:13 PM
    I use a lot of LC brass along with RCBS primer swaging die and I never had any problems seating primers. That RCBS does take quite a bit of force and you have to make sure you go all the way down or it wont fully remove crimp. I actually broke my...
    11 replies | 487 view(s)
  • marek313's Avatar
    11-15-2018, 03:57 PM
    marek313 replied to a thread Powder coat harness in Cast Boolits
    From what I saw somewhere on the net I think its about 26+ BH. Probably depends on the exact type , baking process etc. Copper should be around 35 so little bit harder then powder coat. Shooting lead and PC shouldnt wear out barrels as quick as...
    8 replies | 399 view(s)
  • marek313's Avatar
    11-14-2018, 02:59 PM
    I have PSA 300AAC upper with 16" barrel and pistol gas system. No problems at all unless you form your 300 brass out off .223 brass thats too thick. Thats the only time I had rounds stuck in the chamber but once fired I had no extraction issues...
    10 replies | 447 view(s)
  • marek313's Avatar
    11-12-2018, 05:22 PM
    Thats not a realistic setup for someone that doesnt know much about computers. Me and you can run multi boot platform but Linux isnt for everyone and even more so if you dont specialize in IT and your only familiar with Windows. For standard users...
    25 replies | 713 view(s)
  • marek313's Avatar
    11-12-2018, 04:42 PM
    I'm not a big fan of Staples or Best Buy and their geek squat but anyway. I'm going to leave file transfer alone because I dont know which folders they were going to move etc. Microsoft Office though doesnt come with new PCs. Some might have a 30...
    25 replies | 713 view(s)
No More Results
About marek313

Basic Information

About marek313
Location:
New Jersey

Statistics


Total Posts
Total Posts
263
Posts Per Day
0.62
General Information
Last Activity
Yesterday 03:56 PM
Join Date
10-16-2017
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check