StainLess Steel MediaInline FabricationTitan ReloadingGraf & Sons
MidSouth Shooters SupplyRotoMetals2ADvertise hereLee Precision

  • Mauser 98K's Avatar
    07-15-2018, 03:40 AM
    they a hoot to shoot, that is for sure.. and it is hard to find 500rnds ammo for regular rifles for 5$..
    5 replies | 132 view(s)
  • Mauser 98K's Avatar
    07-14-2018, 09:00 PM
    anyone else shoot past 40m with their pump pellet gun? i recently acquired a Daisy 880 pump that had blown out seals for about 10 cents from recycling center.. i replaced the blown seals with silicon rubber and doubled them up to take higher...
    5 replies | 132 view(s)
  • Mauser 98K's Avatar
    07-13-2018, 08:13 PM
    want to see something cool? here is one that i just finished. yes it is really running off the heat of my hand at 40mV.. the thing draws so little now to light the LED that it almost will not register...
    37 replies | 2247 view(s)
  • Mauser 98K's Avatar
    07-13-2018, 03:12 AM
    this is the schematic Mr_Sheesh.. the new circuit i built Thursday has over 100 turns of wire and a 100,000ohm potentiometer. but this here is my latest circuit that i finished a few hours ago..
    37 replies | 2247 view(s)
  • Mauser 98K's Avatar
    07-12-2018, 10:44 PM
    it was an odd cookie. it kept up like that for 2-3 hours b4 leveling off for another 30 minutes b4 it started falling off like normal... and here i was getting my hopes up....
    37 replies | 2247 view(s)
  • Mauser 98K's Avatar
    07-12-2018, 08:34 PM
    the meter was directly across the battery.
    37 replies | 2247 view(s)
  • Mauser 98K's Avatar
    07-12-2018, 03:44 AM
    what do yall make of this? voltage increasing instead of falling..
    37 replies | 2247 view(s)
  • Mauser 98K's Avatar
    07-12-2018, 12:56 AM
    a little something experimental i have been playing with.. it works lots better than the other systems i have been playing with. lots more efficient with a lot less work.. do not even need a core for it. this system does not work like...
    37 replies | 2247 view(s)
  • Mauser 98K's Avatar
    06-21-2018, 02:48 PM
    Mauser 98K replied to a thread 22lr Pinch Trimming in Swaging
    Pinch trimming is the process of trimming jackets that consist of a lower die that supports the jacket and a tapered trimming punch that pinches the jacket between it and the die thus cutting the jacket and allowing one to remove the excess jacket...
    17 replies | 666 view(s)
  • Mauser 98K's Avatar
    06-20-2018, 10:43 PM
    i finally settled on the final design for my 7.62x25mm defense bullets, so i went through the entire manufacturing process from drawing to polishing and this is what i come up with.. the ones above were just testing, these are the finished product...
    27 replies | 1755 view(s)
More Activity
About Mauser 98K

Basic Information


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Today 06:43 AM
Join Date
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check