Titan ReloadingInline FabricationADvertise hereStainLess Steel Media
Graf & SonsMidSouth Shooters SupplyRotoMetals2Lee Precision

  • Time Killer's Avatar
    02-15-2018, 11:48 PM
    Time Killer started a thread This Old Mold in Cast Boolits
    Did a little casting with the above mold i purchased off eBay. Its a Hensley and Gibbs. With 4 different cavities. H&G # 26 Weighing in at approximately 98gr, H&G # 67 Weighing approximately 115gr, H&G # 87 weighing approximately 83gr and what...
    4 replies | 320 view(s)
  • BT Sniper's Avatar
    02-15-2018, 02:29 PM
    BT Sniper replied to a thread BTSimple 30 cal! in BT Sniper
    Yes, actually I do enjoy it, just takes a bit of time and can be very challenging at times but it is ....... AWESOME when it all comes together! Brian
    24 replies | 867 view(s)
  • BT Sniper's Avatar
    02-15-2018, 01:44 AM
    BT Sniper replied to a thread BTSimple 30 cal! in BT Sniper
    Been busy in shop...... Machined first BTSimple 30 cal die over the weekend. It's capabilities are looking very good. It will make any bullet one wishes from very light to pretty darn heavy. It has a 10s ogive down to a .155 diameter meplat tip....
    24 replies | 867 view(s)
  • BT Sniper's Avatar
    02-08-2018, 01:47 PM
    10s tangent ogive! I also have a 6s ogive reamer. BT
    15 replies | 740 view(s)
  • BT Sniper's Avatar
    02-03-2018, 11:11 PM
    BT Sniper replied to a thread .228 bullets in Swaging
    Simple bump of .224 bullets in a .228 die and good to go.
    14 replies | 592 view(s)
  • BT Sniper's Avatar
    01-31-2018, 09:04 PM
    PM sent on brass.
    2 replies | 246 view(s)
  • BT Sniper's Avatar
    01-31-2018, 02:41 PM
    I try not to get into the political side of things. Simply enjoy finding and sharing good info related to our hobbies, and the info in that thread is good. I only hope he uploaded all those pics directly to the site. It looks like my threads with...
    4 replies | 402 view(s)
  • BT Sniper's Avatar
    01-31-2018, 01:12 PM
    Check out this thread and the process used for applying lube and how much..... pretty incredible thread, http://singleactions.proboards.com/thread/11487/building-benchrest-rifle?page=28
    12 replies | 546 view(s)
  • BT Sniper's Avatar
    01-31-2018, 01:03 PM
    Here is a great thread I found a while back, just the kind that any of us should like, lots of pics! The gentelmen builds a benchrest gun from bare steel and then shows all the steps he uses to make exceptional bullets. The swaging of bullets...
    4 replies | 402 view(s)
  • BT Sniper's Avatar
    01-31-2018, 03:40 AM
    Tumble lube is a very good way to regulate just how much lube to use and get an even coat on all your jackets or cores. Simply need a rotating tumbler and a clean bucket of some sort. Figure out how much lube to use per weight of your jackets...
    12 replies | 546 view(s)
  • BT Sniper's Avatar
    01-29-2018, 12:02 PM
    Yep, I've seen that too. I'm sure my groups would have been a little tighter with a bit more case prep, I was using new Federal brass that was military pull downs, the neck tension on the seated bullet was all over the place. But the whole...
    16 replies | 1042 view(s)
  • BT Sniper's Avatar
    01-29-2018, 03:05 AM
    Got a chance to go out a shoot a few of these 70 grain pills today. Testing was for both accuracy and max FPS in their ability to hold together. I got to say I was successful in both regards. Even though my 22-55AI (as shown in pics above)...
    16 replies | 1042 view(s)
  • Time Killer's Avatar
    01-28-2018, 11:30 PM
    I have a mold that is hollow base and is a challenge to cast with also. Try taking a pencil and rubbing the lead an the pin.
    27 replies | 805 view(s)
  • BT Sniper's Avatar
    01-24-2018, 01:01 PM
    BT Sniper replied to a thread BTSimple 30 cal! in BT Sniper
    Once I post pics it will all be easier to understand and explain. Brian
    24 replies | 867 view(s)
  • BT Sniper's Avatar
    01-23-2018, 05:18 PM
    BT Sniper replied to a thread BTSimple 30 cal! in BT Sniper
    If customer had commercial jackets and cores all they would need is the $595 dies. If they wish to use anything else for a jacket or cast their own cores they need the options. Did this answer the question? BT p.s. the $595 dies come...
    24 replies | 867 view(s)
  • BT Sniper's Avatar
    01-23-2018, 12:19 AM
    BT Sniper replied to a thread BTSimple 30 cal! in BT Sniper
    You guys will be more then happy with the meplat and nose profile of the 30 cal BTSimple. For my BTSniper premium 30 cal customers that wish to use 5.7X28 brass I offer them a .098" diameter meplat, this BTSimple will have a .155" diameter...
    24 replies | 867 view(s)
No More Results
About Time Killer

Basic Information

Statistics


Total Posts
Total Posts
10
Posts Per Day
0.05
General Information
Last Activity
02-18-2018 09:26 PM
Join Date
07-28-2017
Referrals
0

1 Friend

  1. BT Sniper BT Sniper is offline

    Vendor Sponsor

    BT Sniper
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check