RepackboxLee PrecisionMidSouth Shooters SupplyInline Fabrication
RotoMetals2ADvertise hereTitan Reloading

Tab Content
  • kenton's Avatar
    09-26-2020, 09:10 AM
    kenton replied to a thread What's your favorite in Leverguns
    You might like these Henrys then
    20 replies | 251 view(s)
  • kenton's Avatar
    09-26-2020, 08:21 AM
    kenton replied to a thread in Our Town
    I really like their transparent shipping costs, of course I always end up buying more ammo trying to maximize my shipping value. Pretty clever I guess.
    17 replies | 574 view(s)
  • kenton's Avatar
    09-25-2020, 06:56 AM
    kenton replied to a thread Creedmoore? in Cast Boolits
    19 replies | 362 view(s)
  • kenton's Avatar
    09-22-2020, 09:13 AM
    I took the springs out of the butt stock on my 9mm and it eliminated the cheek bite for me. I guess getting rid of the springs help it not move as much.
    38 replies | 750 view(s)
  • kenton's Avatar
    09-15-2020, 01:21 PM I always wanted to make one of these for my BIL's lathe but still haven't gotten around to it. I think it would make a tremendous difference.
    63 replies | 1707 view(s)
  • kenton's Avatar
    09-15-2020, 08:23 AM
    That annoying that your buddy is Bogarting a lathe he will never use but a least it is inside so someday in the future it maybe useful. I know of a few machines that were stored under tarps for a "couple days" five or more years ago that are boat...
    63 replies | 1707 view(s)
  • kenton's Avatar
    09-15-2020, 12:12 AM
    I guess I should say my point wasn't that you need a big lathe but that a well designed and well made lathe is worlds better than a HF lathe. One of my most commonly used lathes at work is a 11x18 Sharp tool room lathe. It is a much more rigid and...
    63 replies | 1707 view(s)
  • kenton's Avatar
    09-14-2020, 04:25 PM
    My brother in law bought a 9x20in HF lathe a few years back. He would get mad at me when I said it was a cool toy. He would demand I acknowledge it was the equal of the lathes I ran at work (I'm a machinist). He finally came around to my point of...
    63 replies | 1707 view(s)
  • kenton's Avatar
    09-13-2020, 09:12 PM
    Looks like a Hatfield with a plastic stock. I have one in .410 that I bought from Walmart for $99. It functions, which is all I really hoped for. The down sides, at least on mine, are: The...
    39 replies | 1269 view(s)
  • kenton's Avatar
    09-11-2020, 06:15 PM
    I haven't done the measuring or math but if you are curious you could get something like this: Measure the number of KW/H you use for a casting session (gonna be a small...
    44 replies | 1294 view(s)
  • kenton's Avatar
    09-09-2020, 10:10 PM
    kenton replied to a thread 20 cent primers in Our Town
    I'm not sure if we are being sarcastic, but
    24 replies | 1002 view(s)
  • kenton's Avatar
    09-08-2020, 10:59 PM
    kenton replied to a thread 20 cent primers in Our Town
    Everyone does realize that "price gouging" is the natural reaction of a well functioning free market economy right? If you want fixed prices you need outside interference from a socialist group. You should be writing the "price gougers" commending...
    24 replies | 1002 view(s)
  • kenton's Avatar
    09-04-2020, 06:06 PM
    kenton replied to a thread Knock about pants in Our Town
    Get some Rit dye and make them what ever color you want, even tie dyed!
    39 replies | 1267 view(s)
  • kenton's Avatar
    09-03-2020, 07:26 AM
    kenton replied to a thread Custom cartridges... in Our Town
    Custom anything is going to be expensive, usually very expensive. Have you looked into case reforming? There is a sub forum specifically for that, you may be able to get help there.
    3 replies | 252 view(s)
  • kenton's Avatar
    08-31-2020, 03:04 PM
    I planted pumpkins and gourds on my berm a few years ago by shooting pumpkins and gourds on my berm after the holidays. they have been growing back ever since. Usually set some of the nicer looking ones on the front step for awhile and shoot the...
    124 replies | 19417 view(s)
  • kenton's Avatar
    08-31-2020, 02:52 PM
    If you are measuring with inch calipers the sprue plate should measure .236" for a 6mm thickness. 8mm would be .315"
    29 replies | 1089 view(s)
  • kenton's Avatar
    08-31-2020, 02:20 PM
    Could you pick one from here? I would look at removing the collar from the broke off screw and using a 10.9 or 12.9 grade M6 screw from the local hardware store. Also another...
    29 replies | 1089 view(s)
  • kenton's Avatar
    08-31-2020, 08:44 AM
    I have never tried smokes copper powder coat but with my light blue I got much better coverage when I moved my storage and shaking operation from my hot humid shed to my cool dry basement. I believe I also put my open powder in the oven at 200ish...
    19 replies | 723 view(s)
  • kenton's Avatar
    08-31-2020, 07:51 AM
    I generally crimp in the crimp groove just for the sake of consistency. But do note that if your round are too long they may not chamber and if they are shorter you may increase your chamber pressure. Additionally if you read the safety notice you...
    9 replies | 473 view(s)
No More Results
About kenton

Basic Information

About kenton


quando omni flunkus moritati


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Today 12:02 AM
Join Date
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check