Titan ReloadingRepackboxWidenersMidSouth Shooters Supply
ADvertise hereRotoMetals2Inline FabricationLee Precision

Tab Content
  • am44mag's Avatar
    06-30-2020, 07:48 PM
    am44mag replied to a thread best forums out there. in Our Town
    The best forums that I've found are as follows Cast Boolits - by far the best for bullet casting knowledge, one of the best if not the best for general reloading knowledge too. It's also one of the few forums where experimenting with new,...
    16 replies | 1260 view(s)
  • am44mag's Avatar
    06-26-2020, 06:48 PM
    How about this. I found two places out of the way where I could possibly put a more permanent berm. One is down in a small hollow and would be up against a thicket. There's a decent sized hill on the backside of it, and it's about 155 yards from my...
    44 replies | 1985 view(s)
  • am44mag's Avatar
    06-24-2020, 03:32 AM
    Do you guys know of a good gunsmith that would sleeve the chamber for a fair price? There are no professional gunsmiths around here, so I will most likely have to ship the gun. About how much would that kind of work cost? Sent from my...
    24 replies | 1830 view(s)
  • am44mag's Avatar
    06-23-2020, 04:51 PM
    Yeah, I really liked the design of those grips. Had they been oversized instead of undersized, I would have been fine with just doing the final fit myself. I think I'll make a set of grips for that revolver. S&W grips are kind of a PITA to make, but...
    46 replies | 2072 view(s)
  • am44mag's Avatar
    06-23-2020, 12:01 AM
    I don't think I can do anything with these, the rear and butt are right on, but the front is bad. It feels fine, but looks bad. I think what they did was angle the grind inwards when cutting that contour. Sent from my SM-G965U using...
    46 replies | 2072 view(s)
  • am44mag's Avatar
    06-22-2020, 11:55 PM
    I could not get a pic of the pitting in the chamber. My camera wouldn't fit low enough into the action to see it, and it's mainly at the front of the chamber. I tried to get a pic of the brass, but I couldn't get a great pic of that either. This one...
    24 replies | 1830 view(s)
  • am44mag's Avatar
    06-21-2020, 09:57 PM
    I'll see if I can't get some pics in the next couple of days so you guys have a better idea of what I'm working with. I can definitely try polishing. Really if I could get it to a point where it extracts well enough that I don't have to...
    24 replies | 1830 view(s)
  • am44mag's Avatar
    06-21-2020, 09:54 PM
    I finally got my set from them. Beautiful grips, but I am not happy with the fit. One side won't go on and the other is off and possibly undersized. I'm also not too happy with the finish on the butt. It's kind of scuffed/faded. I didn't have time...
    46 replies | 2072 view(s)
  • am44mag's Avatar
    06-21-2020, 09:49 PM
    I plan on loading to roughly M80 specs with either BL-C(2) or H4895. I have no reason to want to push this round hard, I have other guns that will do that far better. I think what I'll do is do my load development in the 7.62 cases and see how those...
    31 replies | 3200 view(s)
  • am44mag's Avatar
    06-20-2020, 10:42 PM
    I recently bought a 50-70 Trapdoor and like it, but there is one issue that is bugging me. One area of the chamber has some pitting in it, and it's preventing the brass from fully ejecting. It will extract about 1/4", at which point you can usually...
    24 replies | 1830 view(s)
  • am44mag's Avatar
    06-19-2020, 03:05 AM
    So, I have not been able to find a definitive answer on this. Is there really a difference in 7.62 NATO and .308 Win brass, or for all intents and purposes, are they the same? I've read claims that the 7.62 brass is thicker and will need to be...
    31 replies | 3200 view(s)
No More Results
About am44mag

Basic Information

Age
27
About am44mag
Location:
NE Texas/SE Oklahoma
Interests:
Shooting, reloading, milsurps, casting bullets, woodworking.
Occupation:
Student (Criminal Justice Major, Psycology Minor). Hope to be a Texas State Trooper someday

Signature


______________________________________________
Aaron

Statistics


Total Posts
Total Posts
698
Posts Per Day
0.62
General Information
Last Activity
Yesterday 04:03 PM
Join Date
06-23-2017
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check