Titan ReloadingInline FabricationGraf & SonsADvertise here
StainLess Steel MediaLee PrecisionRotoMetals2MidSouth Shooters Supply

Tab Content
  • Landy88's Avatar
    Yesterday, 03:52 PM
    You are making me hungry. Over basmati is very good and healthier, but an Irish twist of over chips is better yet. Be sure, if having it there or at an authentic pub to tell them spicy - the Irish tame their curries even worse than Brits and...
    11 replies | 201 view(s)
  • Landy88's Avatar
    Yesterday, 03:30 AM
    I guess that I came decades too late to the party, but these would've simplified my loading. The .38spcl and .357 are the only reasons that I even need small primers or their punches.
    25 replies | 2706 view(s)
  • Landy88's Avatar
    Yesterday, 02:43 AM
    RedLegEd, Yours is a very neat and compact kit tailored to a specific task. Nice!
    26 replies | 909 view(s)
  • Landy88's Avatar
    04-12-2018, 02:36 PM
    Landy88 replied to a thread Winchester Model 70 in Factory Rifles
    Good points on quality of the latest crf 70s, but one has to factor in the awful new trigger. Now, if they put an honest M70 trigger back on the current 70fwt...
    26 replies | 870 view(s)
  • Landy88's Avatar
    04-08-2018, 08:54 PM
    Some of the best shooting compact .45s (no direct experience with 9s or .40s) around, but part of how they do it is by weighing as much as a full-size.
    12 replies | 273 view(s)
  • Landy88's Avatar
    04-08-2018, 03:16 AM
    Landy88 replied to a thread Winchester Model 70 in Factory Rifles
    To throw in one more wrinkle: After years of customers or would be ones complaints about post 64 fit and finish Winchester brought out an XTR version 70s - 80s that was still the post 64 / 68 PF action but very nice wood, fit, and finish - these...
    26 replies | 870 view(s)
  • Landy88's Avatar
    04-07-2018, 08:15 PM
    No pics but I use an old milsurped desk much like that. It works well, and the metal in it is usefully heavy gauged stuff. Without an overhang mounting some presses is tricky but doable. Even though it's heavy and sturdy, I still had to brace the...
    13 replies | 511 view(s)
  • Landy88's Avatar
    04-01-2018, 03:53 AM
    Another tack on this could be keeping the loading kit right with the gun. I've seen elegant fitted cases for fine old guns that had places built in for both gun care and loading tools. My own favorite two rifle case has a nylon cover over the...
    26 replies | 909 view(s)
  • Landy88's Avatar
    03-29-2018, 03:22 PM
    Landy88 replied to a thread Venison Roast in Cookin' Recipe's
    These are all cook it til it breaks down methods an other way with venison is to barely cook it. Food borne pathogens are a much smaller risk in venison than in almost any other meat, allowing us to leave it rather rare. Thinking of a venison...
    10 replies | 370 view(s)
  • Landy88's Avatar
    03-29-2018, 01:28 PM
    You've put together a nice box for a nice group of 310 tools. Maybe add foam to pad the scale, only somewhat fragile bit. Your nice wood box is a lot classier than my old video camera case for reloading and old steel toolbox for casting tools,...
    26 replies | 909 view(s)
  • Landy88's Avatar
    03-26-2018, 04:01 PM
    Herco is happier as a +p powder than as a -p powder. Even the so versatile Unique will begin to balk at too reduced of loads.
    8 replies | 437 view(s)
  • Landy88's Avatar
    03-24-2018, 03:08 PM
    I think that I even drooled a bit, then I saw the "LH." A nice LH .54 and 12ga TC New Englander is on GB, if anyone shoots from that shoulder.
    47 replies | 1156 view(s)
  • Landy88's Avatar
    03-24-2018, 02:25 PM
    It is more a case of moving to hand tools for flexibility and something new to try, for me, than of getting back to them, since I was all in from the start with a pretty full RCBS bench-top setup, as a kid, for my loading startup. My parents were...
    33 replies | 1231 view(s)
  • Landy88's Avatar
    03-24-2018, 01:37 AM
    Thanks for the encouragement. I'll keep looking.
    47 replies | 1156 view(s)
  • Landy88's Avatar
    03-22-2018, 03:45 PM
    Good to be reminded that there are some options if one wants (or is forced) to move up a level or two to a custom or semi-custom ML. I'm not there, yet; but I do want a dedicated elk ML. I think that a little bore diameter would for that be a...
    47 replies | 1156 view(s)
  • Landy88's Avatar
    03-21-2018, 11:58 PM
    The .50 has always been the sales leader, but it's big sisters were always in the market. Now, it seems it's almost, to paraphrase Henry Ford, "...available in any caliber you want as long as it is .50."
    47 replies | 1156 view(s)
No More Results
About Landy88

Basic Information

Signature


The first purpose of the Second Amendment is too often overlooked, fostering a liberty of mind and action necessary in the people of a free republic.

Statistics


Total Posts
Total Posts
219
Posts Per Day
0.70
General Information
Last Activity
Today 04:09 AM
Join Date
06-11-2017
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check